Magellan / Spectra SP
21
Part 5: Access Codes
The control panel supports the following access codes:
5.1
Access Code Length
Section
[701]
: System Options
Option
[1]
OFF = 6-Digit Access Codes
Option
[1]
ON = 4-Digit Access Codes (default)
All access codes can be set to lengths of either 4- or 6-digits. When the 4-digit option is selected, entering a 4-digit code will allow
access. Using the 6-digit option, entering 6 digits is required to allow access.
If the access code length is changed from four digits to six digits when access codes have already been
programmed, the control panel will automatically add the last 2 digits by using the first 2 digits. For example, if
the access code is 1234 and you switch to 6 digits, the code will become 123412. Be sure to verify the access
codes after switching from 4-digit access codes to 6-digit codes. When switching from six digits to four digits, the
control panel will simply remove the final two digits of the access code. For example, 123456 will become 1234.
5.2
Installer Code (Default: 0000 / 000000)
The Installer Code is used to enter the system‘s programming mode, which allows you to program all the features, options and
commands of the control panel. The Installer Code can be 4- or 6-digits in length (see
Access Code Length
on page 21) where
each digit can be any value from 0 to 9. The Installer Code cannot be used to program Master Code 1, Master Code 2 or user
access codes. To program the Installer Code press:
[
ENTER
]
+
[
CURRENT
INSTALLER
CODE
]
+
[397]
+
new 4- or 6-digit Installer Code
5.3
Maintenance Code (Default: Empty)
The Maintenance code is similar to the Installer code. It can be used to enter programming mode, which allows you to program all
the features, options and commands
except
for the system’s communication settings (sections
[395]
,
[397]
,
[398]
,
[815]
,
[816]
,
[817]
,
[910]
,
and [911]
) as well as any user codes. The Maintenance code can be 4 or 6 digits in length where each digit can be
any value from 0 to 9. The Maintenance code is empty by default. Set the Maintenance in section
[398]
.
[
ENTER
]
+
[
INSTALLER
CODE
]
+
[398]
+
new 4- or 6-digit Maintenance Code
5.4
System Master Code (Default: 1234 / 123456)
The Installer Code can be used to program the System Master Code. With the System Master Code a user can use any arming
method and can program any user access code, but not the User Code Options. The System Master Code can be 4 or 6 digits in
length, where each digit can be any digit from 0 to 9. The System Master Code can be modified but cannot be erased. To change
the System Master Code press:
[
ENTER
]
+
[
INSTALLER
CODE
]
+
[399]
+
new 4- or 6-digit System Master Code
5.5
User Code Options
Sections
[404]
to
[432]
: Options
[1]
to
[8]
The User Code Options define which arming methods each user can use to arm or disarm the system. Regardless of these
settings, all users can Regular arm assigned partitions and all users except those with the Arm Only option can disarm an
assigned partition, regardless of how it is armed. Select one or more of the options described on the following pages for each
user access code, where sections
[404]
to
[432]
represent user access codes 004 to 032.
5.5.1
Partition 1 Assignment
Sections
[404]
to
[432]
: User codes 004 to 032
Option
[1]
OFF = Deny access to partition 1
Option
[1]
ON
= User code has access to partition 1 (default)
Installer Code
[397]
:
Used to program all control panel settings except user access codes.
Maintenance Code
[398]
:
The Maintenance code is similar to the Installer code. It can be used to enter programming mode, which
allows you to program all the features, options and commands
except
for the panel’s communication
settings. The maintenance code is empty by default.
System Master Code
[399]
:
Provides full access. Arm and disarm using any method described in the
User Code Options
below as
well as program the user access codes.
Master Code 1:
Permanently assigned to partition 1. Same as a regular user code except it can also program access
codes for user codes assigned to partition 1.
Master Code 2:
Permanently assigned to partition 2. Same as a regular user code except it can program access codes
for user codes assigned to partition 2. If the system is not partitioned Master Code 2 will be assigned to
partition 1.
29 User Codes:
Can arm and disarm as per User Code Options on page 21.
