background image

INSTRUCTIONS CM408F

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 13 of 24

Single Hinge Door Handle Direction Reversal

NOTE:  

N

ET

-S

ERV 

cabinet configurations that ship with Single Hinge Doors are hinged on the left side by default.

With single hinge door removed, remove (2) hinge brackets from cabinet frame by removing (2) #10 Phillips screws and (2) #10 lockwashers 
from each bracket and slide bracket out of cabinet frame as shown.  Invert brackets so that bottom-left bracket becomes top-right bracket and 
top-left bracket becomes bottom-right bracket as shown below.  Secure brackets to cabinet post with (2) #10 Phillips screws and (2) #10     
lockwashers per bracket.  Brackets are to be inserted through upper-most opening of cabinet frame.

Reverse door handle orientation by removing cam from door handle assembly and door handle assembly from Single Hinge Door.  Rotate door 
handle assembly 180º.  Rotate orienation of cam stop 90º clockwise while door handle cam and hex bolt are removed from handle assembly.  
Reinstall handle assembly into Single Hinge Door.  See ‘Door Handle Direction Reversal’ view below.  Remove PANDUIT label from bottom of 
door and reinstall label centered and 7-1/4” from top of door.

#10 Phillips Screws and 
#10 lockwashers

(Remove and use to install 
hinge bracket on opposite 
side of cabine frame)

Hinge Bracket

(Tab is to be inserted 
into cabinet frame)

Hinge Bracket Installation and Removal

Door Handle Direction Reversal

FRONT OF CABINET

Remove Hinge Brackets

(See detail view)

Reinstall Hinge Brackets on 
Right Cabinet Post

(Hinge point to be orientated 
towards outside of cabinet)

Remove Door Handle Cam 
and Hex Bolt

Remove Phillips Screw and Bridge Bar

Remove Door Handle, Rotate 180º, and Reinstall Handle

Reinstall Door Handle Cam 
and Hex Bolt

Reinstall Phillips Screw and Bridge Bar

Rotate Orientation of Cam 
Stop 90º Clockwise

(This allows for door 

handle to swing in 

proper direction)

Summary of Contents for NET-SERV Series

























Reviews: