Panduit NET-SERV Series Instructions Manual Download Page 19 | Manualshive

Page: 19 / 24

background image

INSTRUCTIONS CM408F

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 19 of 24

Overhead Cable Openings

Cabinet is equipped with multiple covers and knockouts for cable entry. The bezel inserts can be removed from overhead cable opening bezels
by pulling inserts out of position. Bezels can be removed from cabinet top by depressing tabs and pulling out of position. The remaining knock-
outs can be removed by cutting the (8) tabs with a wire cutter as shown. Additional bezels and bezel inserts are available for purchase.

Removable Bezel Inserts

Overhead Cable Opening Bezel

«
...
17
18
19
20
21
...
»

Summary of Contents for NET-SERV Series

























Reviews:

No comments

Related manuals for NET-SERV Series

NECCare Gold Express5800/320Fd

Brand: NEC Pages: 10

Brand: NEC Pages: 84

NEC Express5800 Series

Brand: NEC Pages: 6

UniServer R2900 G3

Brand: H3C Pages: 15

SSG-2029P-ACR24H

Brand: Supermicro Pages: 136

Brand: IOGear Pages: 44

Brand: StarTech.com Pages: 24

Brand: NEC Pages: 10

Brand: Advantech Pages: 140

Brand: QNAP Pages: 58

TourMaster MLA2504

Brand: Coachsound Pages: 22

ReadiManagerSE200

Brand: Polycom Pages: 4

Brand: W&T Pages: 79

Brand: Dell EMC Pages: 60

Applause Media System

Brand: GILBARCO VEEDER-ROOT Pages: 102

Brand: Intel Pages: 30

Brand: D-Link Pages: 146

Brand: H3C Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands