Panduit NET-SERV Series Instructions Manual Download Page 11 | Manualshive

Page: 11 / 24

background image

INSTRUCTIONS CM408F

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 11 of 24

Vertical Blanking Panels

Bottom blanking panel is shipped uninstalled. To install, remove [1] #10 Phillips screw and [1] #10 lockwasher from each side at bottom of
vertical blanking panels. Position bottom blanking panel over base frame of cabinet and secure with #10 Phillips screws and lockwashers
as shown below.

To adjust depth of vertical blanking panels, loosen (6) #10 Phillips screws on each vertical panel, adjust panels to desired depth and
retighten (12) #10 Phillips screws.

To Adjust:
Loosen (12) #10 Phillips
Screws on each vertical
blanking panel

[6] screws per side

#10 Phillips Screws and
#10 lockwashers

(Remove and use to install
bottom blanking panel)

Bottom Blanking
Panel

«
...
9
10
11
12
13
...
»

Summary of Contents for NET-SERV Series

























Reviews:

No comments

Related manuals for NET-SERV Series

SAT-IP EXIP 418

Brand: Kathrein Pages: 16

SuperServer E300-9A-4C

Brand: Supermicro Pages: 109

Brand: Supermicro Pages: 118

Brand: Abit Pages: 56

Brand: IOGear Pages: 48

Brand: StarTech.com Pages: 24

Brand: Waves Pages: 6

Brand: Time Machines Pages: 24

BizNAS D400 Series

Brand: Tandberg Data Pages: 2

Advanced Office-in-a-Box

Brand: Enconnex Pages: 40

Brand: ACTi Pages: 20

Brand: Lantronix Pages: 100

Brand: FreeNAS Pages: 4

Brand: Check Point Pages: 45

Brand: CTC Union Pages: 40

AS1021M-UR Plus

Brand: Supero Pages: 104

Brand: Supero Pages: 102

Brand: Supero Pages: 102

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands