manualshive.com logo in svg

Panduit NET-SERV Series, Instructions Manual, Page: 20 / 24

Share
Download
Panduit NET-SERV Series Instructions Manual Download Page 20

INSTRUCTIONS CM408F

For Technical Support: www.panduit.com/resources/install_maintain.asp

End Seal Bracket

Page 20 of 24

Vertical Exhaust Duct Mounting

NOTE: 

 For ease of installation, a minimum of (2) persons are suggested for this assembly step.

Lift exhaust duct assembly and position on top of cabinet as shown.  Align large top flange towards front of cabinet.  Secure duct to cabinet 
with (6) #10 x 1/2” Phillips trilobular screws and (6) #10 lockwashers as shown.  Vertical Exhaust Duct is adjustable to allow for tight fit 
against ceiling.  See view below for course and fine duct adjustment instructions (

STEPS 1 and 2)

.  Adjacent Vertical Exhaust Ducts can 

be ganged by securing ganging bracket with (2) #10 x 1/4” long Phillips screws and (2) #10 lockwashers per side as shown.

NOTE:  Some adjustment to the leveling of the base of cabinet may be required for exhaust duct to align with exhaust ducts of adjacent 
cabinets.

Course Duct Adjustment

Remove (4) #10 Phillips screws and (4) #10 lockwashers 
holding upper duct to lower duct.  Raise upper duct to desired 
height and secure using (4) #10 Phillips screws and (4) #10 
lockwashers.  

[(2) additional screws and lockwashers are on rear of duct]

Fine Duct Adjustment (Top Collar)

Loosen (4) #10 Phillips screws holding top collar assembly in 
place.  Position top collar so that seals are secure against 
ceiling and slightly compressed.  Retighten (4) #10 Phillips 
screws.  

[(2) additional screws and lockwashers are on rear of duct]

Vertical Exhaust 
Duct

(6) #10 x 1/2” Phillips 
Trilobular Screws 
and #10 lockwashers

[(3) additional screws and 
lockwashers are on rear of 
duct]

End seal brackets are adjustable to accomodate conditions between ganged cabinets or at the end of a row.  Adjust the end seal bracket by 
loosening (2) #10 nuts per bracket using a 3/8” socket wrench or end wrench.  Extend the end seal bracket and retighten (2) #10 nuts.

Loosen and retighten

#10 nuts to adjust

end seal bracket

Use 3/8” socket wench

or 3/8” end wrench

Vertical Exhaust Duct
Ganging Bracket

(2) #10 x 1/4” Phillips Screws 
and #10 lockwashers

(Front and Back)

Large Top Flange

(align towards front of 
cabinet)

STEP 1

STEP 2

UNDERSIDE VIEW 
OF TOP COLLAR

Summary of Contents for NET-SERV Series

























Reviews:

No comments