P&M Aviation QUIK Operating Instructions Manual Download | Manualshive

Page: 52 / 68

background image

Quik & Quik GT450 Aircraft Operating Instructions

29

th

March 2007

Issue 1

Page 52 of 68

The Power Units

Rotax 912

Rotax 912S

Type

4 stroke

4 stroke

CC

1211

1352

Power

80bhp/5,500rpm

100bhp/5,500 rpm

Ignition

Dual CDI

Dual CDI

Cylinders

4

4

Reduction

2.27:1

2.43:1

Fuel/oil mix

n/a

n/a

Fuel min. rating

95 RON

95 RON

The Rolling Chassis

The  main  structure  of  the  trike  is  of  square  section  high  strength  aluminium  alloy  tube.  A  rigid  composite
tandem seat is fitted which locates onto the tubular seat frame. The seat incorporates a foldable backrest for
the front seat occupant.

The  rear undercarriage comprises Chro-Mo steel alloy tubular wishbones  with  suspension by  polyurethane
elastomer  incorporated  in  the  tubular  aluminium  alloy  struts.  The  braked  main  wheels  are  accessible  by
removing the quickly-detachable wheel spat fins.

The  nose  undercarriage  is  steerable  and  incorporates  footrests  and  throttle/brake  controls.    A  trailing  link
elastomer suspension system is fitted.

The Fuel Tank and System

Fuel is fed from a single fuel tank mounted beneath the seats. The fuel system has a fuel cock and external
filter backed up by an internal strainer fitted to the end of the fuel tank pick-up pipe. External fuel pipes are
fire-resistant to a specification that meets British Civil Airworthiness Requirements - Section S.

The approximate calibration of the fuel tank is as follows:

% Tank Volume

Gauge Reading

0 to 15

0

16 to 27

1/8

28 to 41

¼

42 to 57

7/16

58 to 70

9/16

71 to 85

11/16

86 to 90

7/8

91 to 100

1

Before you place any reliance on your fuel gauge, you will need to calibrate the fuel gauge on your particular
aircraft.    As  is  general  practice  in  aviation,  you  should  visually  check  the  fuel  tanks  to  confirm  that  the
contents match the fuel gauge reading before flying.  When flying, use your watch to time the flight against
known fuel burn at a given rpm, and always leave plenty of fuel in reserve.

CAUTION

Damage may result on CDI engines if the engines are
turned over without the plug leads connected.

Never rely on the fuel gauge accuracy alone
when calculating flight distances left to run. A
forced landing due to running out of fuel could
result in injury or death.

WARNING

GG

!

«
...
50
51
52
53
54
...
»

Summary of Contents for QUIK





































































Reviews:

No comments

Related manuals for QUIK

Brand: Nova Pages: 22

Brand: Topmodel Pages: 20

Brand: SOL paragliders Pages: 18

Brand: SOL paragliders Pages: 24

Brand: Gulfstream Pages: 94

Brand: MAC PARA Pages: 18

Brand: Gulfstream Pages: 16

Brand: XciteRC Pages: 56

Brand: Ozone Pages: 2

Brand: Ozone Pages: 16

Brand: ICON Pages: 9

Brand: Blade Pages: 20

Brand: ICARO paragliders Pages: 20

FAA-STC SA10232SC

Brand: Forced Aeromotive Technologies Pages: 11

Mini Warbirds Rare Bear

Brand: skyangel Pages: 8

Brand: Skywalk Pages: 10

Brand: Remos Pages: 116

Brand: Flow Paragliders Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands