P&M Aviation QUIK Operating Instructions Manual Download | Manualshive

Page: 28 / 68

background image

Quik & Quik GT450 Aircraft Operating Instructions

29

th

March 2007

Issue 1

Page 28 of 68

NOTE!

•

There is no primer bulb on the 912/912S.

Before attempting to start, use the following mnemonic as a final check:

S

ecurity: passenger/ pilot harness attached, no loose objects, brakes ON.

T

hrottles: set to SHUT, choke as required

A

ll clear: all persons & animals clear of propeller arc to the side and prop blast behind

I

gnition: contact switches set as required

M

ixture: fully rich

P

ress/pull: starter action as required

STARTING

: check visually again that the propeller area is clear and call “

Clear Prop

” loudly. Pause. Turn on

the key switch, set the contacts to ON, then push the button in 5 seconds bursts. Release the button as soon
as the engine fires.

If  the  engine  refuses  to  start  after  5  or  6  attempts,  close  the  controls  and  switch  OFF  the  ignition  before
investigation.

6.4. ENGINE WARM-UP

ROTATING  PROPELLERS  ARE  ALMOST  INVISIBLE  AND  CAN  CAUSE  INJURY  OR  DEATH!
Extreme  care  must  be  exercised  during  engine  warm-up.    Ensure  that  all  spectators/children/pets
are kept well clear of the propeller and the propeller arc.

Before touching the propeller, double check that
both contact switches are set to the OFF
(forward) position, failure to do so could result in
injury or death.

Never attempt to hand start an engine by swinging the propeller! This practice is very dangerous
and could result in injury or death.

Although unlikely, it is possible that an electrical circuit fault will allow the ignition circuit to remain live
with the ignition switches in the off position, it is therefore essential that before attempting to clear a
flooded engine with the foot throttle set to OPEN, you ensure that the aircraft has adequate clear
space forward for the operator to react to an inadvertent engine start up and to close the throttles. If
in any doubt, then chock the aircraft before carrying out this procedure.

Do not attempt to start the motor with the
throttles open.

WARNING

!

WARNING

!

WARNING

!

WARNING

!

WARNING

!

«
...
26
27
28
29
30
...
»

Summary of Contents for QUIK





































































Reviews:

No comments

Related manuals for QUIK

Brand: Textron Pages: 500

Brand: Technify Motors Pages: 232

Brand: Wipaire Pages: 49

Brand: STEMME Pages: 211

Brand: Ocean Rodeo Pages: 32

Brand: Ozone Pages: 23

Brand: Team 5 Pages: 100

Brand: Velocity Pages: 36

Cessna Citation 0258

Brand: Textron Pages: 37

fun series 30" Crack Wing

Brand: Twisted Hobbys Pages: 42

Brand: Swing Pages: 8

Brand: Swing Pages: 16

Brand: Swing Pages: 20

Connect Reverse Evo

Brand: Swing Pages: 32

CONNECT REVERSE 3

Brand: Swing Pages: 32

Brand: Swing Pages: 48

Brand: Swing Pages: 48

Brand: FireBird Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands