Panasonic WV-SF448 Operating Instructions Manual Download Page 125 | Manualshive

Page: 125 / 228

background image

•

External:

Uses the audio inputted from the mic or the line input terminal. An audio cable (accessory) must

be connected to the audio cable connector.

•

Default:

Internal

Note

•

When “Privacy action on alarm” is selected in terminal 1 of the alarm settings, “Mic select” can be
separately specified when there is an alarm action. (

®

page 129)

[Audio encoding format]

Select the audio encoding format from G.726 and G.711.

•

Default:

G.726

Note

•

G.711 is available only when “Mic input” is selected for “Audio transmission/reception”.

[Audio bit rate]

Select “16kbps” or “32kbps” for the audio bit rate used to transmit/receive audio data.

•

Default:

32kbps

Note

•

When selecting a smaller value for “Bandwidth control(bit rate)” (

®

page 157) while putting a priority

on the JPEG image transmission, select “16kbps” for “Audio bit rate”.

•

[Audio bit rate] is unavailable when “G.711” is selected for “Audio encoding format”.

[Mic input volume (Camera to PC)]

Select a volume level on the PC to hear audio transmitted from the camera.

•

Mic High:

The volume level will become high. This setting will be applied when audio is input to the camera

using a microphone.

•

Mic Middle:

The volume level will become middle. This setting will be applied when audio is input to the

camera using a microphone.

•

Mic Low:

The volume level will become low. This setting will be applied when audio is input to the camera

using a microphone.

•

Line High:

The volume level will become high. This setting will be applied when audio is input to the camera

using the Line input.

•

Line Middle:

The volume level will become middle. This setting will be applied when audio is input to the

camera using the Line input.

•

Line Low:

The volume level will become low. This setting will be applied when audio is input to the camera

using the Line input.

•

Default:

Mic Middle

[Mic input interval (Camera to PC)]

Select an interval for audio reception from the following.
20ms/ 40ms/ 80ms/ 160ms

•

Default:

40ms

Note

•

When a shorter interval is selected, the delay time will be shorter. When a longer interval is selected,
audio interruption may be diminished even though the delay time will be longer. Select the interval
according to the network environment.

[Audio output volume (PC to Camera)]

Select a volume level on the camera to hear audio transmitted from the PC.
High/ Middle/ Low

Operating Instructions

125

11 Configure the settings relating to images and audio [Image/Audio]

«
...
123
124
125
126
127
...
»

Summary of Contents for WV-SF448





































































































































































































































Reviews:

No comments

Related manuals for WV-SF448

Brand: Zivif Pages: 14

Lumix H-FS14140

Brand: Panasonic Pages: 28

Brand: Campbell Pages: 116

Brand: NAPCO Pages: 80

Brand: Guardian Pages: 2

Brand: Ziton Pages: 13

Brand: Abus Pages: 2

Brand: Zhejiang Uniview Technologies Pages: 28

Brand: Vitek Pages: 16

Brand: Amcrest Pages: 17

Brand: Streamax Pages: 8

Brand: SHANY Pages: 22

Brand: Uniden Pages: 20

Brand: Huazheng Pages: 10

Brand: Konig Pages: 48

Brand: Robotics Technologies Pages: 11

Brand: e2v Pages: 50

Brand: ADEMCO Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands