Panasonic WV-SF448 Operating Instructions Manual Download Page 183 | Manualshive

Page: 183 / 228

background image

When the registration window is not displayed, check that the PC is being connected to the Internet,
and click the reload button of the browser.

3.

Register the information for “Viewnetcam.com” by following the instructions of the wizard.

→

When the message “The new camera is successfully registered to Viewnetcam.com” is displayed, close
the registration window.
The URL set at the time of registration can be used for camera access. However, this URL is unavailable
when accessing the camera from the PC connected to the same network (LAN).

Note

•

When the registration for the “Viewnetcam.com” service is completed, the URL registered for
“Personal(Camera) URL” is displayed. It may take up to about 30 minutes until the URL of the registered
camera is validated.

•

To cancel the enrollment in the “Viewnetcam.com” service, access the “Viewnetcam.com” website
(http://www.viewnetcam.com/) later.

•

When “Expired” is displayed in the URL of “Viewnetcam.com” in the viewnetcam settings page or the
status page, restart the camera after registering the “Viewnetcam.com” service. After restarting the
camera, check that the registered URL is displayed in the URL of “Viewnetcam.com” of [Status] -
[Viewnetcam.com] on the “Maintenance” page.

•

It is possible to check the information registered for the “Viewnetcam.com” service by accessing the
URL displayed beside “Your Account Link”. When the URL is not displayed, check that the PC is being
connected to the Internet, and click the [Set] button.

•

If access often fails due to the change in the global address of router, set a smaller value for “Access
interval”.

16.4.4 Checking the information registered for the
“Viewnetcam.com” service

It is possible to check if the camera has been registered for the “Viewnetcam.com” service. (

®

page 196)

Operating Instructions

183

16 Configuring the network settings [Network]

«
...
181
182
183
184
185
...
»

Summary of Contents for WV-SF448





































































































































































































































Reviews:

No comments

Related manuals for WV-SF448

Brand: Eaton Pages: 32

Brand: Observint Pages: 2

Brand: Panasonic Pages: 124

Brand: DAKOTA ULTRASONICS Pages: 163

Brand: TAC Pages: 20

Brand: FBII Pages: 83

Brand: FBII Pages: 10

Brand: NA-DE Pages: 8

Brand: jablotron Pages: 16

RoboSHOT 12 HD-SDI

Brand: VADDIO Pages: 73

Brand: Data Harvest Pages: 21

Brand: Inline Pages: 2

Brand: Speco Pages: 104

LoRa Custos WWDLW Series

Brand: UbiTech Pages: 17

Brand: Atsumi Electric Pages: 2

Brand: QHYCCD Pages: 27

Brand: Burg Wächter Pages: 12

Brand: COMPRO Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands