manualshive.com logo in svg

Panasonic WV-CS850, Operating Instructions Manual

Share
Download
Panasonic WV-CS850 Operating Instructions Manual Download Page 45

45

• The following steps of installation and connection should be taken by qualified service personnel or

system installers and should conform to all local codes.

• Make sure to switch the camera off before installation and connection.
• Do not install the camera near the air outlet of an air conditioner.

Camera Mounting Base

Camera

Camera Mounting 
Base

Fixing Screw

Loosen and 
Push

1

2

3

4

ON

1

2

3

4

ON

5

6

7

8

8-bit DIP SW

4-bit DIP SW

INSTALLATION

1. Disassembling the camera

(1) Loosen the fixing screw to separate the

camera mounting base and the camera.
Push up the screwdriver once before
removing the screw.

(2) Turn the camera mounting base ap-

proximately 15 degrees counter clock-
wise and remove the base from the
camera.

2. Setting the switches

There are two DIP switches on the camera:
an 8-bit switch and a 4-bit switch. The 8-bit
DIP switch is used in both ways to imple-
ment protocol selection and to specify the
unit number. The 4-bit DIP switch selects
termination ON/OFF and half/full duplex
selection for RS485 communications. Switch
settings are read in to the camera when the
power is turned on. Make sure to turn it off,
then turn it back on after changing the
switch settings. Switch positions and func-
tions are shown below.

RS485 Parameter Setup

The selected protocol, communication para-
meters, and set unit numbers are read into
the camera when power is switched on.

1. Set the switch according to the function

shown in the table.

2. Switch off the camera.
3. Switch on the camera to read in the

changed switch settings.

Note:

The changed communication

parameters are displayed on the
RS485 SETUP menu after the cam-
era is switched on.

Precautions

15

°

Turn 15

°

Then

Camera 
Mounting Base

Remove 
from the 
Camera

1

2

3

4

ON

5

6

7

8

1

2

3

4

ON

5

6

7

8

Switch Position

Protcol Selection

Panasonic’s conventional

Panasonic’s NEW generation

1

2

3

4

ON

5

6

7

8

1

2

3

4

ON

5

6

7

8

1

2

3

4

ON

5

6

7

8

Switch Position

Paramater Selection

BAUD RATE

1

1

1

NONE

NONE

NONE

8

8

8

19 200

  9 600

  4 800

DATA BIT

PARITY 

CHECK

STOP 

BIT

Intelligent Security & Fire

Summary of Contents for WV-CS850


























































Reviews:

No comments

Brands by name

Popular brands

Load more brands