manualshive.com logo in svg

Panasonic WV-CS850, Operating Instructions Manual

Share
Download
Panasonic WV-CS850 Operating Instructions Manual Download Page 21

21

■

Auto Mode Selection

1. To set auto mode

Move the cursor to AUTO MODE and select a mode by moving
the joystick to the left or right. Modes change as follows:

   *** SET UP MENU ***
PRESET 1*
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 DIGITAL FLIP
 LOCAL/REMOTE
 SPECIAL1
CAMERA
RS485 SET UP

15
10MIN
AUTO PAN
SEQ
OFF
LOCAL

Setup menu

2. When AUTO PAN is selected, set details as follows:

Move the cursor to AUTO PAN 

and press the CAM (SET) key to

display the AUTO PAN setting menu.

3. To set a panning start position and panning end position

Follow the steps below.

(1) Move the cursor to POSITION SET and press the CAM (SET)

key.
The cursor moves to START.

(2) Move the joystick to the left or right to select a panning start

position and press the CAM (SET) key.
This determines the start position and the cursor moves to
END.

(3) Move the joystick to the left or right to select a panning end

position and press the CAM (SET) key.
This determines the end position and the cursor moves to
POSITION SET.

4. To set a panning speed

Move the cursor to SPEED, and move the joystick to the left or
right to set a panning speed.
The panning speed increases when the joystick is moved to the
right, and decreases when it is moved to the left.

Caution:

If the panning range is changed after the camera has not

panned for a long time or has been panning in the same panning
range, the picture may not be clear or noise may appear. If this is
the case, pan the camera fully several times.
If this does not eliminate the problem, refer servicing to qualified
service personnel.

5. To set pan limit ON/OFF

Move the cursor to PAN LIMIT and select ON or OFF by moving
the joystick to the left or right.

ON:

Manual pan is limited from the start point to the end point

specified by POSITION SET.  Set endless turn to OFF before
pan limit is set to ON.

OFF:

Manual pan is not limited.

Note:

When ON is set, manual pan moves the camera away from

the other side of the start-end range.

    ** AUTO PAN **

POSITION SET

SPEED

PAN LIMIT
ENDLESS
STOP TIME

RET

START
END
••••|••••
L       H
OFF
OFF
1S

AUTO PAN setting menu

    ** AUTO PAN **

POSITION SET

SPEED

PAN LIMIT
ENDLESS
STOP TIME

RET

START
END
••••|••••
L       H
OFF
OFF
1S

    ** AUTO PAN **

POSITION SET

SPEED

PAN LIMIT
ENDLESS
STOP TIME

RET

START
END
••••|••••
L       H
OFF
OFF
1S

    ** AUTO PAN **

POSITION SET

SPEED

PAN LIMIT
ENDLESS
STOP TIME

RET

START
END
••••|••••
L       H
OFF
OFF
1S

OFF

SEQ

SORT

AUTO PAN

Intelligent Security & Fire

Summary of Contents for WV-CS850


























































Reviews:

No comments

Brands by name

Popular brands

Load more brands