1. CAMERA SETUP MENU
This camera utilizes a user setup menu that is displayed on-screen.
• Opening the Setup Menu
Press and hold down
for 2 seconds or
more.
The CAM SET UP menu appears on the
monitor as shown at right.
Check the current settings on the menu.
Refer to the sections below for a detailed description of menu items. If you decide not to
make any changes after checking the current settings, move the cursor to END at the start
of the bottom line, and press
to close the CAM SET UP menu and return to normal cam-
era picture mode.
Note:
If no button is pressed for 6 minutes while the CAM SET UP menu or any other menu
is opened, the menu is automatically closed and the mode returns to the normal cam-
era picture.
2. SETUP OPERATION
This camera utilizes a user setup menu
(CAM SET UP) that is displayed on the
monitor.
To set items on the CAM SET UP menu, use
the following buttons on the side panel.
Up Button
(
)
:
Moves the cursor
upwards. Use this button to select an item or adjust the parameters.
Down Button
(
)
: Moves the cursor downwards. Use this button to select an item or
adjust the parameters.
Right Button
(
)
: Moves the cursor to the right. Use this button to select or adjust the
parameters of the selected item. The parameter changes each time
this button is pressed.
Left Button
(
)
:
Moves the cursor to the left. Use this button to select or adjust the
parameters of the selected item. The parameter changes each time
this button is pressed.
Set Button
(
)
:
Executes selections and displays a submenu for an item with
mark.
END: Close Setup menu.
RET: Return to the previous menu.
To return to the CAM SET UP menu
Move the cursor to RET and press
. The CAM SET UP menu appears.
• All Reset Operation
All Reset allows you to reset all setup menu items to the factory default settings if you are
unsure about the correct settings. Proceed as follows:
(1) Make sure that the CAM SET UP menu is not displayed (a camera picture is displayed).
(2) While pressing both
and
, press
for a few seconds. The message ALL
RESET momentarily appears on the monitor.
This resets all adjustments and parameters to the factory default settings.
• Editing the CAM SET UP Menu
Important Notice:
When the SET UP DISABLE appears in the bottom line of the CAM SET UP menu, you
cannot change the currently active settings. This is to prevent accidental changing of
the settings.
To edit the CAM SET UP menu (change
settings),
press and or and
to move the cursor to SET UP DIS-
ABLE in the bottom line.
Press
. SET UP DISABLE changes
to SET UP ENABLE. Move the cursor to
END, then to the item(s) you want to
change.
• Editing the SPECIAL Menu
To edit the SPECIAL menu (change set-
tings), proceed as for editing the CAM SET
UP menu above. Move the cursor to END
after the SET UP ENABLE appears. Then
press and simultaneously
(holding
down
and press
) for 2 seconds or
more.
The SPECIAL menu appears on the moni-
tor. Select the item to be changed and
change the setting as described for the
CAM SET UP menu.
Important Notice:
When the cursor is moved to END and the CAM SET UP menu closed after changing
the parameters, the new values are saved in the EEPROM (Electric Erasable and
Programmable Read Only Memory). These values remain valid until new values are
saved, even if the power of the camera is off.
↵
Left Button
Right
Button
Down
Button
Up
Button
** CAM SET UP **
CAMERA ID OFF
ALC/ELC ALC
SHUTTER OFF
AGC ON
SENS UP OFF
WHITE BAL ATW
AUDIO LEVEL ....I....
- +
END SET UP DISABLE
↵
↵
↵
** CAM SET UP **
CAMERA ID OFF
ALC/ELC ALC
SHUTTER OFF
AGC ON
SENS UP OFF
WHITE BAL ATW
AUDIO LEVEL ....I....
- +
END SET UP ENABLE
↵
↵
↵
SETUP
↵
↵
↵
** CAM SET UP **
CAMERA ID OFF
ALC/ELC ALC
SHUTTER OFF
AGC ON
SENS UP OFF
WHITE BAL ATW
AUDIO LEVEL ....I....
- +
END SET UP DISABLE
Highlighted
(To be continued reverse page)
** SPECIAL **
UP SIDE DOWN OFF
CHROMA GAIN ....I....
AP SHARP ....I....
PEDESTAL .I.......
- +
CAMERA RESET PUSH SW
RET END
Set Button
