Panasonic WRKT4504E Series Reference Manual Download Page 9 | Manualshive

Page: 9 / 40

background image

Switching/Blind Actuator

9

3.2

Device behaviour after ETS download

Switchin Function:

If output channel is configured as switching after ETS download related channel will be off.

Status led will also be off. If manual control is activated from ETS output channels can be controlled via
control buttons on device.

Blind/Shutter Function:

If output channel pair is configured as Blind/Shutter after ETS download related

channels will be off. Status leds will also be off.   Blind/Shutter will stay on current possion.  If manual control is
activated  from  ETS  output  channels  can  be  controlled  via  control  buttons  on  device.    For  blind/shutter
configuration  after  ETS  download  device  don’t  know  exact  position  of  the  blind/shutter  so  device  does  not
send feedback or respond to down comments until move to the upper position.

Attention:

After ETS download all blind/shutter configured channels must be moved to upper position.

3.3

Device behaviour after bus failer

This can be configured from ETS for every channel. Switchin and blind/shutter configuration has different
behaviour options.

3.4

Device behaviour after mains failer

After main failure all output channels will be off.

3.5

Device behaviout after main or bus recovery

This can be configured from ETS for every channel. Switchin and blind/shutter configuration has different
behaviour options.

«
...
7
8
9
10
11
...
»

Summary of Contents for WRKT4504E Series









































Reviews:

No comments

Related manuals for WRKT4504E Series

Brand: Valve Concepts Pages: 15

Brand: Lawler Pages: 5

Brand: Balboa Pages: 12

Brand: Paoli Pages: 16

Brand: Saitek Pages: 4

Brand: Bartlett Pages: 5

Brand: HABONIM Pages: 9

Brand: Harpo Pages: 35

Brand: Hardi Pages: 2

Brand: jbc Pages: 4

Brand: jbc Pages: 4

Brand: EasySMX Pages: 11

Brand: EasySMX Pages: 8

Brand: Watlow Pages: 4

Brand: Parker Pages: 38

Brand: Parker Pages: 2

Serial Interface Module

Brand: Federal Signal Corporation Pages: 12

Brand: XP Metal Detectors Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands