manualshive.com logo in svg

Panasonic WRKT4504E Series, Reference Manual

Share
Download
Panasonic WRKT4504E Series Reference Manual Download Page 18

    Switching/Blind Actuator 

 

 

 

 

18 

 

 

4.1.2.4

 

Pulse Function and Parameters 

Basic functionality: If the Function parameter is Pulse, then the channel works for Pulse  function. 
A "1" on the switching object switches the channel ON for the duration of a pulse length.  If a "1" is 
sent  again  during  this  switch-on  phase  then  the  channel  remains  switched  on  for  the  duration  of  a 
further  pulse  length.  If  a  "0"  is  sent  during  this  switch-on  phase  then  the  channel  switches  off 
immediately. 

 

Name 

Values 

Description 

Function 

Switching  

 

On/Off Delay 

 

Pulse 

 

Staircase light timer with 

prewarning function 

 

This function specifies the function type of the channel. 
There are four type of selection function for each channel. 

Type of contact 

Normally open 

 

Normally close 

 

This parameter sets the contact position of each channel 
at startup (i.e when mains voltage applied to the module) 

Time base for pulse length 

1 sec 

 

10 sec 

 

30 sec 

 

1min 

 

This parameter value is  multiplied with the “pulse length 
factor” parameter for defining the total pulse length time. 

Factor for pulse length 
(1..255 x timebase) 

*1…

5

…255]  Defines  the  total  pulse  length  time  with  “time  base  for 

pulse length” parameter. 
Pulse length = time base* factor 
 

Input logic 

None 

 

Lock 

 

And 

 

Override 

None:

 The channel only reacts to the switching object in 

the way described at the beginning.  

Lock:

  If the linking object is set  to "1" then no pulse can 

be  started.  The  linking  object  has  no  meaning  for  pulses 
which  are  already  running(i.e.  if  it  is  started  ,  it 
accomplishes  the  pulse  time,  OFF  and  disable  the 
channel).  

And:

 If the linking object is set to "0" then no pulse can be 

started.  The  linking  object  has  no  meaning  for  pulses 
which  are  already  running.  (i.e.  if  it  is  started  ,  it 
accomplishes the pulse time) 

Override:

  If  the  linking  object  is  set  to  "1"  then  the 

channel is switched on regardless of the switching object. 
Any waiting pulses are deleted during an override. 
 

 

 
 
 

Summary of Contents for WRKT4504E Series









































Reviews:

No comments

Brands by name

Popular brands

Load more brands