Panasonic Super Dynamic III WV-CW974 Operating Instructions Manual Download Page 41

Page: 41 / 374

Auto tracking settings

LARGE

Zooms the target to a size that is
approximately three-fourths (vertically)
the size of the monitor screen.

Notes:

• Sizes shown above are approximate and for

reference only. The actual size depends on
operating environment conditions and tracking
conditions.

• A larger target size setting will result in reduced

tracking performance.

(3) Configuring the Detection Sensitivity Setting

(SENSITIVITY)

1. Move the cursor to SENSITIVITY and then tilt the

joystick left or right to select a sensitivity setting.
You can set sensitivity to one of three levels: LOW,
MID, or HIGH.
The factory default setting is MID.

Note:

A low sensitivity setting can avoid erroneous

detection of tree movement and other natural
movement, but it also reduces tracking performance.
Higher sensitivity, on the other hand, improves tracking
performance but also increases the chance of
detection error. Configure settings in accordance with
the environment where the camera is located.

(4) Configuring the Tracking Activation Mode

Setting (TRACKING MODE)

1. Move the cursor to TRACKING MODE and then tilt

the joystick left or right to select how much weight
should be given to a target's characteristic features
(shape or colour etc.) during tracking.
TRACKING MODE can be set to LOW, MID, or
HIGH.

LOW :

Weight given to movement.

⇑⇓

HIGH :

Weight given to characteristics.
The factory default setting is MID.

Note:

When LOW is selected, tracking may switch to

another target that is exhibiting a large degree of
movement. When HIGH is selected, tracking of a
particular target continues, but tracking performance is
reduced when the conditions of the on-screen target
change. Configure this setting in accordance with the
environment where the camera is located.

(5) Configuring the Zoom Control Setting while

Tracking (ZOOM CONTROL)

Zoom control can be set to OFF, INTERMIT or
CONTINUOUS.

1. Move the cursor to ZOOM CONTROL and then tilt the

joystick left or right to select a zoom control setting.

OFF

Zoom control is not performed.

INTERMIT

Zoom control is performed as
many times as needed during
motion detection.
Zoom control is done once during
auto tracking.

-41-

■

Using the Auto Tracking Setup

Menu

Display the auto tracking setting menu from the setup
menu to configure camera settings. The auto tracking
setting menu appears first.

1. Display the setup menu (page 24), move the cursor to

AUTO TRACKING

, and then press the camera

(set) button.
This will display the auto tracking setting menu.
* Items

through

below explain each of the

items available on the auto tracking setting menu.

(1) Configuring the Installation Height Setting (CAM-

ERA HEIGHT)

1. Move the cursor to CAMERA HEIGHT and then tilt

the joystick left or right to specify a camera height
setting.
You can set the camera height in the range of
2.50M to 30.0M. The factory default setting is
2.50M.
The installation height of the camera should be the
height between the tracking target and the camera
(H1: 2.50M ~ 30.0M). It is not H2.

Important:

Make sure that you input the installation

height of the camera correctly. An incorrect camera
height value will result in extremely poor detection and
tracking performance.

(2) Configuring the Target Size Setting (OBJECT

SIZE)

1. Move the cursor to OBJECT SIZE and then tilt the

joystick left or right to select a tracking target size
setting.
Size can be set to SMALL, MEDIUM, or LARGE.

SMALL

Zooms the target to a size that is
approximately one-fourth (vertically) the
size of the monitor screen.
This is the factory default setting.

MEDIUM :

Zooms the target to a size that is
approximately one-half (vertically) the
size of the monitor screen.

** AUTO TRACKING **
CAMERA HEIGHT
OBJECT SIZE
SENSITIVITY
TRACKING MODE
ZOOM CONTROL
AUTO RELEASE
LOST MODE
ALARM
AREA SET
INDICATOR
RET TOP