-29-
(2) Press the CAM (SET) button to mask the cell.
Moving the cursor to a cell that is already
masked causes the blinking pattern of the
cursor to alternate between horizontal stripes
and white.
Pressing the CAM (SET) button while the cursor
is located at a masked cell cancels the masking
of the cell.
To cancel all masking areas, press the F3
button.
(3) After masking all of the cells you want, press the
MON (ESC) button to return to the ALC CONT
menu in step 1.
6. Move the cursor to LEVEL, and then tilt the joystick
left and right to adjust the picture output level
(picture contrast).
If you selected ON in step 3 of this procedure, best
results can be obtained by setting a contrast level
that is somewhat high. A contrast level that is too
high, however, may increase the tendency of
afterimages and noise.
Note:
If operation of the system controller's IRIS
(OPEN, CLOSE) button during operation is done
after the menu is closed, the LEVEL on the
CAMERA menu is reflected and stored for these
settings. However, if the camera is in a preset
position, it is reflected as a parameter of the preset
position. To return to the initial factory default level,
execute the system controller's iris reset.
(3) Shutter Speed (SHUTTER)
1. Move the cursor to SHUTTER, and then tilt the
joystick left or right to select a shutter speed
setting.
Tilting the joystick cycles through the shutter speed
settings display in the sequence shown below.
(unit: sec)
When SUPER-D
3
3
is turned off
When SUPER-D
3
3
is turned on
AUTO:
This setting, by moving the shutter
automatically when necessary, provides a
clearer picture of extremely bright objects
outdoors, etc. This is the factory default
setting.
OFF :
Fixed at 1/50 seconds.
Notes:
• When AUTO is selected for the shutter setting,
fluorescent lighting may cause flickering of the
picture. If this happens, select OFF or 1/120 for
the shutter speed setting.
• AUTO is disabled when MANUAL is selected for
light control (ALC/MANUAL) and FIX is selected
for electronic sensitivity enhancement (SENS UP).
(4) Gain Control (AGC)
1. Move the cursor to AGC, and then tilt the joystick
left or right to select a gain control setting.
ON (LOW) :
Low gain
ON (MID) :
Medium gain. This is the factory default
setting.
ON (HIGH) :
High gain
OFF
:
Fixed gain
Note:
When AGC is turned on, the noise reduction
function automatically activates under low illumination
to reduce digital noise. This also, however, can cause
afterimages to be generated by moving objects, and
by panning and tilting the camera. For more
information, see the DNR setting (page 31).
(5) Electronic Sensitivity Enhancement (SENS UP)
1. Move the cursor to SENS UP, and then tilt the
joystick left or right to select an electronic sensitivity
enhancement setting.
The electronic sensitivity enhancement setting can
be changed only when OFF or AUTO is selected for
the shutter speed (SHUTTER) setting. Tilting the
joystick cycles through the settings display in the
sequence shown below. The factory default setting
is OFF.
When SUPER-D
3
3
is turned off
When SUPER-D
3
3
is turned on
Notes:
• The following are the differences between AUTO
and FIX.
AUTO:
Selecting X32 AUTO, for example,
automatically increases sensitivity, up to
a maximum of 32 times.
FIX
:
Selecting X32 FIX, for example,
increases sensitivity 32 times.
The FIX settings cannot be selected when the
shutter speed (SHUTTER) setting is 1/120.
• SENS UP is set to 2x automatically if it is set
higher than 2x when auto tracking starts.
Caution:
Turning on SENS UP can cause digital noise
and white spots (blemish) to appear in the picture.
OFF
↔
AUTO
↔
1/120
↔
1/250
↔
1/500
↔
1/1000
1/10000
↔
1/4000
↔
1/2000
OFF
↔
AUTO
OFF
↔
X2 AUTO
↔
X4 AUTO
↔
X6 AUTO
↔
X10 AUTO
↔
X16 AUTO
X16 FIX
↔
X10 FIX
↔
X6 FIX
↔
X4 FIX
↔
X2 FIX
↔
OFF
X32 FIX
X32 AUTO
↔
↔
↔
↔
OFF
↔
X2 AUTO
↔
X4 AUTO
↔
X6 AUTO
X32 AUTO
↔
X16 AUTO
↔
X10 AUTO
WV-CW970 974̲ENG.qxd 07.2.1 11:31 AM ページ29
