Chapter 5
Operations — Network connection
ENGLISH - 217
Note
f
A LAN cable is required to use the network function.
f
Use a straight or crossover LAN cable that is compatible with CAT5 or higher. Either the straight or the crossover cable, or both cables
can be used depending on the system configuration. Consult your network administrator. The projector will determine the type of the cable
(straight or crossover) automatically.
f
Use a LAN cable of 100 m (328'1") or shorter.
Example of network connections via a twisted-pair-cable transmitter
/
Attention
f
When a LAN cable is directly connected to the projector, the network connection must be made indoors.
Note
f
For the LAN cable between the twisted-pair-cable transmitter and the projector, use a cable that meets the following criteria:
g
Conforming to CAT5e or higher standards
g
Shielded type (including connectors)
g
Straight-through
g
Single wire
g
Diameter of the cable core is same or larger than AWG24 (AWG24, AWG23, etc.)
f
The maximum transmission distance between the twisted-pair-cable transmitter and the projector is 100 m (328'1") for the signal with
resolution of 1 920 x 1 200 dots or less. For the signal with the resolution exceeding 1 920 x 1 200 dots, the maximum transmission distance
is 50 m (164'1"). It is possible to transmit up to 150 m (492'2") if the twisted-pair-cable transmitter supports the long-reach communication
method. However, the signal that the projector can receive is only up to 1080/60p (1 920 x 1 080 dots, dot clock frequency 148.5 MHz)
for the long-reach communication method. If these distances are exceeded, image may be disrupted or a malfunction may occur in LAN
communication.
f
When laying cables between the twisted-pair-cable transmitter and the projector, confirm that cable characteristics are compatible with
CAT5e or higher using tools such as a cable tester or cable analyzer.
When a relay connector is used, include it in the measurement.
f
Do not use a hub between the twisted-pair-cable transmitter and the projector.
f
To transmit the Ethernet and serial control signals using the <DIGITAL LINK IN/LAN> terminal, set the [NETWORK] menu
→
[ETHERNET
TYPE] to [DIGITAL LINK] or [LAN & DIGITAL LINK].
f
To transmit the Ethernet signal using the <LAN> terminal, set the [NETWORK] menu
→
[ETHERNET TYPE] to [LAN] or [LAN & DIGITAL
LINK].
f
The <DIGITAL LINK IN/LAN> terminal and the <LAN> terminal equipped on the projector as standard are connected inside of the projector
when the [NETWORK] menu
→
[ETHERNET TYPE] is set to [LAN & DIGITAL LINK]. Do not directly connect the <DIGITAL LINK IN/
LAN> terminal and the <LAN> terminal using a LAN cable. Construct the system so that it is not connected to the same network via the
peripherals such as the hub or the twisted-pair-cable transmitter.
f
Do not pull cables forcefully. Also, do not bend or fold cables unnecessarily.
f
To reduce the effects of noise as much as possible, stretch out the cables between the twisted-pair-cable transmitter and the projector
without any loops.
f
Lay the cables between the twisted-pair-cable transmitter and the projector away from other cables, particularly power cables.
f
When laying multiple cables, run them side by side along the shortest distance possible without bundling them together.
f
After laying the cables, go to the [NETWORK] menu
→
[DIGITAL LINK]
→
[DIGITAL LINK STATUS] and confirm that the value of [SIGNAL
QUALITY] is displayed in green which indicates normal quality.
f
For twisted-pair-cable transmitters of other manufacturers of which the operation has been verified with the projector, visit the following
website.
https://panasonic.net/cns/projector/
Confirmation of operation for the devices of other manufacturers has been performed with the items set independently by Panasonic
Connect Co., Ltd., and not all the operations are warranted. For operation or performance problems caused by the devices of other
manufacturers, contact the respective manufacturers.
Computer
Projector
LAN cable (straight)
LAN cable (straight)
LAN cable (straight)
Twisted-pair-cable transmitter
Switching hub