Chapter 2
Getting Started — Connecting
60 - ENGLISH
Connecting example: AV equipment
For <HDMI IN 1> / <HDMI IN 2> terminals
Note
f
When HDMI signal is input, switching of the setting in the [DISPLAY OPTION] menu
→
[HDMI IN]
→
[HDMI1] / [HDMI2]
→
[EDID SELECT]
may be required depending on the connected external device or the input signal.
f
For the HDMI cable, use an HDMI High Speed cable that conforms to the HDMI standards. However, when the following 4K image signal
exceeding the supported transmission speed of the HDMI High Speed cable is to be input, use the HDMI cable supporting the high speed
transmission of 18 Gbps such as the one with Premium HDMI cable authentication.
g
An image signal with high specification color depth and gradation such as 3840 x 2160/60p 4:2:2/36-bit or 3840 x 2160/60p 4:4:4/24-bit
Images may be disrupted or may not be projected when an image signal exceeding the supported transmission speed of the HDMI cable is
input.
f
The <HDMI IN 1> / <HDMI IN 2> terminals of the projector can be connected to an external device equipped with a DVI-D terminal using an
HDMI/DVI conversion cable. However, this may not function properly for some external devices, and image may not be projected.
For <SDI 1 IN> / <SDI 2 IN> / <SDI 3 IN> / <SDI 4 IN> / <SDI OUT> terminals of the Function Board
This is an example when the optional 12G-SDI Terminal Board (Model No.: TY-SB01QS) is installed in <SLOT>.
TY-SB01QS
1 IN
4 IN
3 IN
2 IN
OUT
3G SDI
12G/3G SDI
TY-SB01QS
1 IN
4 IN
3 IN
2 IN
OUT
3G SDI
12G/3G SDI
TY-SB01QS
1 IN
4 IN
3 IN
2 IN
OUT
3G SDI
12G/3G SDI
TY-SB01QS
1 IN
4 IN
3 IN
2 IN
OUT
3G SDI
12G/3G SDI
Note
f
Use a cable of 5C-FB or higher (such as 5C-FB or 7C-FB) to properly transmit images when transmitting the HD-SDI signal or the 3G-SDI
signal. It is recommended to use a cable of L-5.5CUHD manufactured by Canare Electric Co., Ltd. when transmitting the 12G-SDI signal.
f
The maximum cable length that can be used is as follows. However, this maximum cable length is a rough guideline, and does not
guarantee the transmission distance.
g
Input and output of HD-SDI signal and 3G-SDI signal: 100 m (328'1")
g
Input of 12G-SDI signal: 80 m (262'6") (when using a cable of L-5.5CUHD), 20 m (65'7") (when using a cable of 5C-FB)
g
Output of 12G-SDI signal: 50 m (164'1") (when using a cable of L-5.5CUHD), 20 m (65'7") (when using a cable of 5C-FB)
f
Use the BNC connector that is compatible with the coaxial cable and type of the signal to be used.
f
Setting the [DISPLAY OPTION] menu
→
[SLOT IN] is required depending on the connected external device or the input signal.
f
The <SDI OUT> terminal is an active through terminal to output the SDI signal (HD-SDI/3G-SDI/12G-SDI) input to the <SDI 1 IN> terminal.
f
The <SDI 2 IN> / <SDI 3 IN> / <SDI 4 IN> terminals are used when the quad link signal is input. These terminals do not support input of
12G-SDI signal.
f
To input the quad link signal, use the cable with same length and same type for connecting to each of <SDI 1 IN> / <SDI 2 IN> / <SDI 3 IN>
/ <SDI 4 IN> terminals. The image may not be projected correctly when the difference of the cable length is 4 m (13'1") or more.
Blu-ray disc player
12G-SDI signal output compatible device
HD-SDI signal, 3G-SDI signal, 12G-SDI signal
f
Directly connect the projector with the external device that will output the signal without going through a distributor, etc., when inputting quad
link signals. A phase difference is generated between the signals of Link 1, Link 2, Link 3, and Link 4, and the image may not be projected
correctly.
f
An error in signal detection may occur when an unsteady signal is input to the projector. In such case, set the [DISPLAY OPTION] menu
→
[SLOT IN] to the content corresponding to the input signal.
For <SDI OPT 1 IN> / <SDI OPT 2 IN> / <SDI OPT OUT> terminals of the Function Board
This is an example when the optional Function Board for 12G-SDI Optical (Model No.: TY-SB01FB) is installed in
<SLOT>.
TY-SB01FB
SIGNAL
SDI OPT
12G/3G/HD
1 IN
2 IN
OUT
TY-SB01FB
SIGNAL
SDI OPT
12G/3G/HD
1 IN
2 IN
OUT
Attention
f
The SFP module to be installed on this product is a Class 1 laser product. Do not look into the SFP module or the connector of the optical
fiber cable with the power of the projector turned on. Your eyes may be damaged when the laser goes into your eyes.
Note
f
Prepare the commercially available SFP module and the optical fiber cable required for connection according to the usage, video signal to
be input, specification of the external device to be connected, etc.
f
The transmission distance may become shorter and the image may not display correctly when there is dust on the connector of the SFP
module or optical fiber cable, or it is dirty. Attach the protection cap or cover supplied by each product to the connector of the SFP module or
the optical fiber cable if the optical fiber cable is not connected.
12G-SDI signal output compatible device
HD-SDI signal, 3G-SDI signal, 12G-SDI signal
SDI - optical converter
Optical fiber cable
