PROJECTOR SETUP menu
ENGLISH -
79
Settings
When [MODE] is set to [AUTO]
Q
Press ▲▼ to select [LINK].
5 )
Press ◄► to switch [LINK].
6 )
The setting will change as follows each time
z
◄► is pressed.
OFF
GROUP A
GROUP D
GROUP C
GROUP B
OFF
Brightness is corrected using the
brightness sensor of one of the
projectors, without linking with other
projectors.
A smaller [BRIGHTNESS CONTROL
GAIN] value means the constant
brightness can be maintained for longer.
GROUP
A - D
Brightness is corrected using brightness
sensors of multiple projectors linked
with each other.
Up to 4 groups from A to D can be set
within the same sub-network using
the network function that links multiple
projectors.
Up to 8 projectors can be registered in
1 group and linked with each other.
Press ▲▼ to select [APPLY].
7 )
Press <ENTER> button.
8 )
The selected [MODE] and [LINK] are activated,
z
then the [BRIGHTNESS CONTROL STATUS]
screen will be displayed.
If <ENTER> button is pressed while [MODE] of
z
the brightness control is not switched to [OFF],
the lamp power at the time is saved as the
reference power.
If <ENTER> button is pressed while [LINK] is
z
[GROUP A - D], the group name is displayed on
the screens of the projectors that are set in the
same group.
Note
When setting [MODE] of the brightness control to [AUTO]
z
or [PC], execute brightness control with the shutter open
for at least 2 minutes.
If the shutter is closed within about 10 minutes after
z
the lamp is turned on while the brightness control is set
to [MODE], [AUTO], or [PC], the brightness cannot be
measured. In this case, the brightness may be corrected
about 2 minutes after the shutter is opened.
While [MODE] of the brightness control is set to [AUTO]
z
or [PC], the [DYNAMIC IRIS] function is kept [OFF (No
correction)].
While [MODE] of the brightness control is set to [AUTO]
z
or [PC], the [LAMP POWER] is fixed to [HIGH] or [LOW].
When changing the lamp power, return [MODE] of the
brightness control to [OFF], then change the lamp power
and adjust the brightness control again.
While [MODE] of the brightness control is set to [AUTO]
z
or [PC], the lamp power is measured automatically
about 8 minutes after the lamp is turned on and then
corrected so that the screen brightness will be the same
as the reference brightness when the brightness control
is executed. The lamp power is not measured for about
8 minutes after the lamp is turned on as it does not
stabilize within this period.
While [MODE] of the brightness control is set to [AUTO],
z
if the lamp is kept on for more than 25 hours, the
brightness is corrected automatically every 25 hours.
While [LAMP SELECT] is set to [DUAL] and [MODE]
z
is set to [AUTO], if the lamp goes off, the brightness is
corrected as much as possible about 1 minute after.
While [MODE] of the brightness control is set to [AUTO]
z
and [LINK] is set to [OFF], the brightness is corrected
until the maximum quantity of correction is achieved.
The brightness may be dispersed largely because of dust
z
sticking to the lens, screen, or inside of the projector,
depending on the environment in which the projector has
been installed.
If the brightness fluctuates significantly because of aging
z
of the lamp or if the lamp has been replaced, re-adjust
the brightness control.
BRIGHTNESS CONTROL STATUS
J
This function displays the status of the brightness
control.
Press ▲▼ to select [BRIGHTNESS
1 )
CONTROL STATUS].
Press <ENTER> button.
2 )
The [BRIGHTNESS CONTROL STATUS]
z
screen will be displayed.
LINK
GROUP A
Summary of Contents for PT-DS100XE ( )
Page 130: ......
