background image

Setting remote control signals for home 
theatre systems

٨

٨

This remote control is programmed with remote control signals for Panasonic products at the  
time of purchase. If you would like to operate devices from other manufacturers, or if your  
Panasonic products cannot be operated, the following setting operations will be required.

To operate home theatre system devices other than the projector, set the remote control signals for 
operating those devices into the remote control.

Do not use the learning function to record remote control signals from other learning remote controls that have  
been learnt by those remote controls. If this is done, operating errors may result.
If no operations are carried out for 60 seconds or more during the setup stage, operation will time out and the  
setting mode will be cancelled.

Setting remote control signals for home theatre systems

You can delete remote control signals which have been programmed into the remote control.

Deleting home theatre equipment remote control signals

Deleting settings all at once  
(OPS RESET)

If you would like to cancel a setting before  
it is complete··

Press "SETUP".

Press "RETURN".

Tip

To return to the previous  
step in an operation

Tip

㧼㧥

㧼㧤

Deleting settings for each button one 
 by one (DELETE)

㧼㧥

For home theatre system devices for which you do not know the device code, 
you can use the search function to search or and set the device code.

Setting home theatre system devices when you do not 
know the device code

㧼㧣

You can have all remote control signals learnt all at once by entering the device 
code which appears in the device code list .

Selecting and entering device codes

㧼㧢

You can freely assign the remote control signals for your home theatre system 
devices to the buttons of this remote control one by one.

Learning remote control signals directly from home 
theatre system devices

Note:

E

NGLISH 

- 5

Summary of Contents for PT-AE1000E

















Reviews: