background image

To finish, press "SETUP".

2

3

1

Press "SETUP" for 3 seconds or more.

Press "SYSTEM" for 3 seconds or more.

6

4

5

Press "SYSTEM".

Press "SYSTEM" once more.

1

٨

٨

(Example: When "USER3" is selected)

Clearing the macro function

Using the power supply macro 
function

Configuration de la fonction macro 
d'alimentation

Turning the power for home theatre 
system devices on and off  at once 
(power supply macro function)

If the distance that the projector's remote control has to 
operate is too far, or if the remove control receiver of the 
home theatre system devices are obstructed, this operation 
may not work correctly.
Check the locations and directions of the home theatre 
system devices to make sure that they can all be operated.

The length of time required for the macro function to finish  
operating effectively will vary depending on the number of 
devices that have been registered.

When you have finished selecting devices,  
press "ENTER".

The macro function will be cleared and the display will 
flash more slowly.

The display will show the  
devices hat have been  
registered by the macro.

If a registered device is selected, the display will  flash 
faster.

If a registered device is selected, the display will flash 
faster.
To register or delete another device, repeat steps 4 and 5.
Clearing the macro function.

Use the tilt button to select "PJ", and then  
press "ENTER".

Press "ENTER", 2 times.

Use the tilt button to select the device to  
be registered.

At the time of purchase, a macro for turning the power on and off for PJ, DVD, VCR and AMP all at once is set.

Note:

Note:

You can use the projector's remote control to turn the power on and off for home theatre system 
devices that have been registered by the remote control.

The power supply for all  
registered devices will turn on.

12 - 

E

NGLISH

Summary of Contents for PT-AE1000E

















Reviews: