Panasonic Panafax UF-585, Service Manual

Page: 147 / 310

147
070 LINE ERROR • 128 lines
• 256 lines
• 512 lines
• 1024 lines
• 2048 lines
• Off (Unlimited) 1. Selects the line disconnect condition during
reception. If the number of line errors exceed this
setting, the unit will disconnect the line.
2. Selects the transmit condition of RTP/PIP or
RTN/PIN.
(Available if No.73 ERROR DETECT is set to
"LINES") (See Note 1)
071 TOTAL ERROR 1 = 5%
2 = 10%
3 = 15%
4 = 20% Selects the transmit condition of RTP/PIP or RTN/
PIN.
(Available if No.73 ERROR DETECT is set to
"RATE") (See Note 2)
072 CONTINUOUS ERROR 1 = Off (unlimited)
2 = 3 lines/STD
3 = 6 lines/STD
4 = 12 lines/STD Selects the continuous total error criteria of Off/3/6
or 12 lines in Standard mode. If continuous total
error exceeds this setting, the unit will transmit
RTN/PIN. (Available if No.73 ERROR DETECT is
set to "RATE")
073 ERROR DETECT 1 = Lines
2 = Rate Selects the error detect condition Lines/Rate.
074 RTN RECEIVE 1 = Disconnect
2 = Continue Selects whether to disconnect the phone line or
continue when "RTN" is received.
075 CODING 1 = MH (MH only)
2 = MR (MH or MR)
3 = MMR (MH or MR or MMR) Selects the coding scheme.
076 Not used
077 RX JAM LENGTH 1 = Off (unlimited)
2 = 2 m
3 = 8 m Selects the maximum length of a document that
can be received per page before disconnecting the
telephone line.
078
079 Not used
080 DOC TOP FEED -5.0 mm
~
+5.0 mm Adjusts the distance between the scanning sensor
ON position and the scanning start position.
081 DOC END FEED -5.0 mm
~
+5.0 mm Adjusts the distance between the scanning sensor
OFF position and the scanning end position.
082 JAM LENGTH 1 = 1 m
2 = 2 m
3 = 8 m
4 = Unlimited Selects the maximum length of the document that
can be scanned.
083 Not used
084 LINE AS NO PAPER 1 = Ring (ring)
2 = Busy (keep line busy) Selects whether to ring or send a busy tone to the
remote station when the recording paper runs out
or the unit cannot receive because of any trouble.
085 Not used
086 Not used
087 DARKER LEVEL 0 = Darkest Contrast
~
15 = Lightest Contrast Selects the scanning contrast level.
0
← →
15
Darkest
←→
Lightest
088 NORMAL LEVEL
089 LIGHTER LEVEL
090 PRINT DENSITY 1 = Normal
2 = Darker Print Density sometimes gets light at low Humidity
condition. In this case, selects “2:Darker”
091 Not used
092 SMOOTHING 1 = Off
2 = On Selects whether the smoothing function is
available.
093
~
129
Not used
130 BUSY-ACK TIMING • In Busy
• While Busy
• After Busy Selects the signal timing between the BUSY and
ACK signal in Printer Interface Mode.
131 CMD RCV GRD TIMER 1 min
~
15 min Selects the guard timer between each GDI
Command in Printer Interface Mode.
132 PRT DATA TIMER 1 min
~
15 min Selects the guard timer between each GDI Data
Frame in Printer Interface Mode.
133 COLLATION (PRT) 1 = Off
2 = On
3 = Auto Selects the Print Collation in Printer Interface
Mode.
When "Auto" is selected, print collation will operate
according to the setting in Fax Parameter #65.
Function Parameter Table
No. Parameter (see Note 3) Selections Function