manualshive.com logo in svg

Panasonic KXF-4T3C, Operating Instructions Manual

Share
Download
Panasonic KXF-4T3C Operating Instructions Manual Download Page 29

Page 29

HOW TO SEE DESCRIPTION FOR OPERATION

The description depends on each page, but basic structure is as follows.

1-1-1

Starting Production

1. Press  

Production

 .

• “Return to origin” for all axes are carried out.

MARKS USED IN THIS MANUAL

In this manual, the following marks are used for description.

443C-E-MMA00-A04-00

T i t l e

T i t l e

Actual operation

Actual operation

Supplementary description on operation

Supplementary description on operation

Operating procedure number

Operating procedure number

: These show operation flow.

: These show operation (cause) and

effect.

: This shows referential item.

: This shows engineer’s operation.

: This shows pressing a key on

touch panel.

: This means pressing 

UNLOCK

 and then

START

 on operating panel within 2

seconds.

: This means pressing B key while

holding A key.

UNLOCK

START

A

B

+

Engineer

Summary of Contents for KXF-4T3C













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands