Panasonic KX-TG2000CB Operating Instructions Manual Download Page 100

Page: 100 / 108

100

Problem

The unit does not work.

“

Out of range.

Move closer to

base & try again

” is

displayed and an alarm
tone sounds.

Static, sound cuts in/out,
fades. Interference from
other electrical units.

The unit does not ring.

You cannot dial.

The display is blank.

You cannot program
function items, such as the
line selection.

Before Requesting Help

With the cordless handset

Remedy

•

Charge the battery fully (p. 16).

•

Clean the charge contacts and charge
again (p. 17).

•

Install the battery properly (p. 93).

•

Re-install the battery and place the handset
on the charger. Try again.

•

The handset has not been registered to the
base unit. Register the handset. (p. 21, 58).

•

You are too far from the base unit.
Move closer to the base unit and try again.

•

Raise the base unit antenna.

•

Locate the cordless handset and the base unit
away from other electrical appliances (p. 4).

•

Move closer to the base unit.

•

Raise the base unit antenna.

•

The ringer volume is set to OFF. Select
HIGH or LOW (p. 24).

•

If 2 other handsets or the base unit and
another handset are in use, the unit may
not ring. The handset and base unit users
will hear incoming call tones.

•

The handset is removed from the ring group.
Add to the ring group (p. 25).

•

The dialed number is restricted. To cancel,
see page 56.

•

Key lock mode is set. Cancel the mode by
pressing and holding

(FUNCTION)

•

Charge the battery fully (p. 16).

•

Programming is not possible while in the
talk or intercom mode, or while listening to
messages.

•

Do not pause for over 60 seconds while
programming.

•

Make sure that the handset is in the
standby mode.

Summary of Contents for KX-TG2000CB













































































































Search results

Summary of Contents for KX-TG2000CB

Reviews:

Related manuals for KX-TG2000CB

Brands by name

Popular brands

Panasonic KX-TG2000CB, Operating Instructions Manual

Search results

Summary of Contents for KX-TG2000CB

Reviews:

Related manuals for KX-TG2000CB

Brands by name

Popular brands