Panasonic KX-TCD410ALM Service Manual Download Page 6

Page: 6 / 109

- When using Ni-Cd batteries (250 mAh):

Talk time: 4hrs approx.
Standby time: 40hrs approx.
(Times indicated are for peak performance)

- The batteries reach peak performance after several full charge/

discharge cycles.

- The batteries cannot be overcharged unless they are repeatedly

removed and replaced.

- If battery life is shortened then please check that battery and charge

terminals are clean.

- For maximum battery life, it is recommended that the handset is not

recharged until battery icon flashes

4.4. Replacing the Batteries

If the

icon flashes after a few telephone calls even when the handset batteries have been

fully charged, 2 batteries must be replaced.
Charge new batteries for approximately 7 hours before initial use.
When replacing the batteries, ensure that the correct battery type is selected.

- To exit the operation, press

any time.

- When Ni-Cd batteries are fitted with the

setting in

icon will disappear and stop charging even if the handset is

on the cradle.

Summary of Contents for KX-TCD410ALM














































































































Search results

Summary of Contents for KX-TCD410ALM

Reviews:

Related manuals for KX-TCD410ALM

Brands by name

Popular brands

Panasonic KX-TCD410ALM, Service Manual

Search results

Summary of Contents for KX-TCD410ALM

Reviews:

Related manuals for KX-TCD410ALM

Brands by name

Popular brands