Panasonic KX-MB2085CXW Service Manual Download Page 41 | Manualshive

Page: 41 / 276

background image

41

KX-MB2085CXW/KX-MB2090CXW

6.9.2.

Circuit Diagram of FAN

Two FAN motors are controlled by following one circuit.
So the operation of two FAN motors (Full speed rotation/Half speed rotation/Stop) are controlled simultaneously.

6.9.3.

Fan Control

For the control of FAN speed, comparator IC (IC504) is used.
This IC compares (+) side input level and (-) side input level.
If (+) side input level is bigger than (-) side input level, output of this IC is "OPEN".
If (+) side input level is less than (-) side input level, it outputs "L" level.

6.9.3.1.

Half Speed Mode

In half speed mode, Q602 outputs pulse (frequency is about 30KHz, duty is about 37.5%).
This pulse is integrated by R530 and C502 then Pin2_IC504 becomes approx. DC1.24V. Input level of IC504_pin2 is determined by
the voltage of between R425.
If voltage between R425 is less than 1.24V, output of pin1_IC504 becomes "H".
Then both Q424, Q421 and Q422 are turned on. So voltage between R425 (=the voltage of IC504_pin2) rises gradually.
When the voltage between R425 exceeds 1.24V, output of pin1_IC504 becomes "L".
Then both Q424, Q421 and Q422 are turned off. So voltage between R507 falls gradually.
By repeating these sequences, voltage between R425 is controlled approx. 1.24V.
On the other hand, if FAN voltage is represented Vo and voltage between R425 is represented VL, VL is determined as below for-

mula.

VL=Vo*R425/(R430+R425)

→

Vo=VL*(R430+R425)/R425

Since each value is as follows, Vo is determined approx. 9.7(V).

VL=1.24(V), R430=150(Kohm), R425=22(Kohm)
Vo=1.24*(150K+22K)/22K=9.7(V)

Therefore by reducing the voltage of FAN power supply, FAN rotates with half speed.

6.9.3.2.

Full Speed Mode

In full speed mode, IC300_pinK25 outputs constant 3.3V.
When Q424, Q421 and Q422 are turned on, Vo becomes approx 20V (approx. 4V drops between R428/R443).
So the voltage between R425 is determined as follows

VL=Vo*R425/(R430+R425)=20*22K/(150K+22K)=2.5(V)

Since IC504_pinA3 is 3.3V and IC504_pinA2 is 2.5V, IC504_pin1 is always "H".
Consequently all Q424, Q421 and Q422 are always turned on, and then approx. 20V is supplied to FAN motors.
Therefore FAN rotates with full speed.

6.9.3.3.

FAN stop

When IC300_pinK25 is "L", both Q424, Q421 and Q422 are turned off, then both FAN stop rotation.

6.9.3.4.

Rotation detect signal

During the FAN rotation, the pulse signal is output from pin 2 of FAN motors as the rotation detects signals.

«
...
39
40
41
42
43
...
»

Summary of Contents for KX-MB2085CXW





















































































































































































































































































Reviews:

No comments

Related manuals for KX-MB2085CXW

Brand: Fenix Imvico Pages: 88

Brand: Oki Pages: 28

Documax A6300 Series

Brand: DataSouth Pages: 180

Brand: Xerox Pages: 13

Phaser 6700V/DX

Brand: Xerox Pages: 162

Brand: Xerox Pages: 3

accuriopress c6085

Brand: Konica Minolta Pages: 81

Brand: Parkside Pages: 77

Brand: Oce Pages: 76

Brand: Oki Pages: 78

Brand: SIGN RACER Pages: 73

CHAMPION MSP 450

Brand: TVS electronics Pages: 92

Brand: Riso Pages: 266

C11C418001 - Stylus C60 Inkjet Printer

Brand: Epson Pages: 64

C11C417001 - Stylus Photo 820 Color Inkjet Printer

Brand: Epson Pages: 2

C11C417001 - Stylus Photo 820 Color Inkjet Printer

Brand: Epson Pages: 2

C11C294131BZ - LX 300+ B/W Dot-matrix Printer

Brand: Epson Pages: 100

C117001-N - DFX 5000+ B/W Dot-matrix Printer

Brand: Epson Pages: 186

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands