Panasonic KX-MB2085CXW Service Manual Download Page 7 | Manualshive

Page: 7 / 276

background image

7

KX-MB2085CXW/KX-MB2090CXW

2 Warning

2.1.

About Lead Free Solder (PbF: Pb free)

Note:

In the information below, Pb, the symbol for lead in the periodic table of elements, will refer to standard solder or solder that con-
tains lead.

We will use PbF solder when discussing the lead free solder used in our manufacturing process which is made from Tin, (Sn),
Silver, (Ag), and Copper, (Cu).

This model, and others like it, manufactured using lead free solder will have PbF stamped on the PCB. For service and repair
work we suggest using the same type of solder although, with some precautions, standard Pb solder can also be used.

Caution

• PbF solder has a melting point that is 50

°

~ 70

°

F, (30

°

~ 40

°

C) higher than Pb solder. Please use a soldering iron with tempera-

ture control and adjust it to 700

°

± 20

°

F, (370

°

± 10

°

C). In case of using high temperature soldering iron, please be careful not to

heat too long.

• PbF solder will tend to splash if it is heated much higher than its melting point, approximately 1100

°

F, (600

°

C).

• If you must use Pb solder on a PCB manufactured using PbF solder, remove as much of the original PbF solder as possible and

be sure that any remaining is melted prior to applying the Pb solder.

• When applying PbF solder to double layered boards, please check the component side for excess which may flow onto the

opposite side (See figure, below).

2.1.1.

Suggested PbF Solder

There are several types of PbF solder available commercially. While this product is manufactured using Tin, Silver, and Copper,
(Sn+Ag+Cu), you can also use Tin and Copper, (Sn+Cu), or Tin, Zinc, and Bismuth, (Sn+Zn+Bi). Please check the manufac-
turer’s specific instructions for the melting points of their products and any precautions for using their product with other
materials.
The following lead free (PbF) solder wire sizes are recommended for service of this product: 0.3mm, 0.6mm and 1.0mm.

«
...
5
6
7
8
9
...
»

Summary of Contents for KX-MB2085CXW





















































































































































































































































































Reviews:

No comments

Related manuals for KX-MB2085CXW

DC240 - DocuColor 240 Color Laser

Brand: Xerox Pages: 2

ColourLaser series guide

Brand: Xante Pages: 31

Brand: Xante Pages: 31

Accel-a-Writer 812

Brand: Xante Pages: 12

Aficio SP C420DN

Brand: Ricoh Pages: 4

Brand: SEWOO Pages: 17

Brand: Tektron Pages: 72

V16 Automatic Shaker Unit

Brand: Garment Printer Ink Pages: 21

Brand: Oce Pages: 268

Brand: ABLE Systems Pages: 12

Brand: Posnet Pages: 2

Brand: DAKEWE Pages: 94

C5020N - FS Color LED Printer

Brand: Kyocera Pages: 410

634dte - X B/W Laser

Brand: Lexmark Pages: 148

4400B - Phaser B/W Laser Printer

Brand: Xerox Pages: 24

Brand: 3nStar Pages: 44

Brand: EBS Pages: 20

Brand: OKIDATA Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands