Panasonic KX-MB2085CXW Service Manual Download Page 262 | Manualshive

Page: 262 / 276

background image

8

Close the top cover by holding the indentations on
both sides of the unit, until locked.

Caution:

R

To prevent injuries, be careful not to put your
hands under the top cover.

When to replace the toner cartridge and drum
cartridge

When the display shows the following, replace the toner
cartridge.
–

“

TONER EMPTY

”

When the display shows the following, the toner cartridge
is coming to the end of its useful life. Please be prepared
to replace the cartridge soon.
–

“

TONER LOW

”

When the display shows the following, replace the drum
cartridge.
–

“

DRUM LIFE LOW

”

–

“

DRUM LIFE OVER

”

Toner cartridge life and drum cartridge life

R

See page 111 for information on the toner life and
drum life.

R

To check the drum life and quality, please print the
printer test list (page 109) and refer to page 111 for
information on the drum life. If the printing quality is
still poor or

“

DRUM LIFE OVER

”

appears on the

display, replace the toner cartridge and drum
cartridge.

R

To maintain print quality and machine life, we
recommend that you clean slots and openings
(page 4) and the inside of the unit (page 105, 108)
when replacing the toner cartridge and/or drum
cartridge.

Note:

R

To ensure that the unit operates properly, we
recommend the use of

Panasonic toner cartridge

and drum cartridge

. See page 7 for accessory

information.

Waste disposal method

Waste material should be disposed of under conditions
which meet all national and local environmental
regulations.

Toner save feature

If you want to reduce toner consumption, set the toner
save setting to ON (feature #482 on page 59). The
toner cartridge will last approximately 20 % longer. This
feature may lower the print quality.

12

1. Introduction and Installation

«
...
260
261
262
263
264
...
»

Summary of Contents for KX-MB2085CXW





















































































































































































































































































Reviews:

No comments

Related manuals for KX-MB2085CXW

Brand: Oki Pages: 17

Brand: Oki Pages: 12

Brand: Oki Pages: 30

Brand: Oki Pages: 391

Brand: Oki Pages: 2

Brand: Oce Pages: 192

Brand: Oce Pages: 22

Brand: Oce Pages: 41

Brand: Oce Pages: 28

Brand: Oce Pages: 6

Brand: QMS Pages: 104

Brand: Oce Pages: 386

Brand: Oce Pages: 2

Brand: Oce Pages: 27

Brand: Oce Pages: 324

Brand: VASTEX Pages: 2

imageRUNNER 4570

Brand: Canon Pages: 154

4150S - WorkCentre B/W Laser

Brand: Xerox Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands