Panasonic KX-MB2085CXW Service Manual Download Page 188

Page: 188 / 276

188

KX-MB2085CXW/KX-MB2090CXW

15 Maintenance

15.1. Maintenance Items and Component Locations

15.1.1. Outline

MAINTENANCE AND REPAIRS ARE PERFORMED USING THE FOLLOWING STEPS.

Periodic maintenance

Inspect the equipment periodically and if necessary, clean any contaminated parts.

Check for breakdowns

Look for problems and consider how they arose.
If the equipment can be still used, perform copying, self testing or communication testing.

Check equipment

Perform copying, self testing and communication testing to determine if the problem originates from the transmitter, receiver
or the telephone line.

Determine causes

Determine the causes of the equipment problem by troubleshooting.

Equipment repairs

Repair or replace the defective parts and take appropriate measures at this stage to ensure that the problem will not recur.

Confirm normal operation of the equipment

After completing the repairs, conduct copying, self testing and communication testing to confirm that the equipment operates
normally.

Record keeping

Make a record of the measures taken to rectify the problem for future reference.

15.1.2. Maintenance Check Items/Component Locations

15.1.2.1. Maintenance List

NO.

OPERATION

CHECK

REMARKS

Document Path

Remove any foreign matter such as paper.

—

Rollers

If the roller is dirty, clean it with a damp cloth then dry thor-
oughly.

Refer to

Maintenance Check Items/Com-

ponent Locations

(P.188)

Sensors

Document sensor (PS54), Read position sensor (PS53), regis-
tration sensor (PS51), Pickup sensor (SW50), Print timing sen-
sor (PS52), Toner sensor (IC51), Top cover sensor (SW1), Exit
sensor (PS50), confirm the operation of the sensors.

See

Maintenance Check Items/Compo-

Glass

If the glass is dirty, clean them with a dry soft cloth.

Refer to

Maintenance

(P.188).

Abnormal, wear and tear
or loose parts

Replace the part. Check if the screws are tight on all parts.

—

Summary of Contents for KX-MB2085CXW





















































































































































































































































































Search results

Summary of Contents for KX-MB2085CXW

Reviews:

Related manuals for KX-MB2085CXW

Brands by name

Popular brands

Panasonic KX-MB2085CXW, Service Manual

Search results

Summary of Contents for KX-MB2085CXW

Reviews:

Related manuals for KX-MB2085CXW

Brands by name

Popular brands