Panasonic KX-FC175AL Page 23 Operating Instructions Manual Download

Page: 23 / 96

Volume

Adjusting handset volume

Handset receiver volume

3 levels (high/middle/low) are available.
While talking, press

To turn the ringer off:

Press and hold

until you hear 2 beeps

in step 4.

●

To turn the ringer back on, press

step 4.

While the ringer volume is set to off:

When receiving a call, the handset will not
ring.

Ringer

off

Ringer volume

4 levels (high/middle/low/off) are available.
While the unit is idle, press

●

If any documents are in the document entrance,
you cannot adjust the ringer volume. Confirm
that there are no documents in the entrance.

To turn the ringer off:

1. Press

repeatedly until the following is

displayed.

Display:

2. Press

●

To turn the ringer back on, press

While the ringer volume is set to off:
When a call is received, the unit will not ring and
will display the following.

Ringer pattern

●

You can select one of three ringer patterns. Change
the setting (feature #17 on page 71). The ringer
pattern you selected will sound when the unit receives
a call.

INCOMING CALL

RINGER OFF

RINGER OFF= OK?
YES:SET/NO:STOP

Adjusting base unit volume

Speaker volume

8 levels (high to low) are available.
While using the speakerphone, press

Fax voice guidance
volume

9 levels (high to off) are available.
While listening to the fax voice
guidance, press

Answering device
volume

9 levels (high to off) are available.
While listening to the recorded
messages, press

Ringer volume

3 levels (high/low/off) are available.
Make sure the handset is idle.

1. Press

œ–

2. Press

to select “Ringer volume”.

Display:

3. Press

)

4. Press

to select the desired volume.

●

The current ringer will sound.

●

To change the volume, press

again within 5 seconds.

Save

Summary of Contents for KX-FC175AL

































































































Search results

Summary of Contents for KX-FC175AL

Reviews:

Related manuals for KX-FC175AL

Brands by name

Popular brands

Panasonic KX-FC175AL, Operating Instructions Manual

Search results

Summary of Contents for KX-FC175AL

Reviews:

Related manuals for KX-FC175AL

Brands by name

Popular brands