background image

- 3 -

This does not guarantee no destruction, no malfunction, or waterproofing in all conditions.

*1 This means that this unit can be used underwater for specified time in specified pressure in 

accordance with the handling method established by Panasonic.

*2 “MIL-STD 810F Method 516.5-Shock” is the test method standard of the U.S. Defense 

Department, which specifies performing drop tests from a height of 122 cm, at 26 orientations 
(8 corners, 12 ridges, 6 faces) using 5 sets of devices, and passing the 26 orientation drops 
within 5 devices. (If failure occurs during the test, a new set is used to pass the drop orientation 
test within a total of 5 devices.)
Panasonic’s test method is based on the above “MIL-STD 810F Method 516.5-Shock”. 
However, the drop height was changed from 122 cm to 150 cm dropping onto 3 cm thick 
plyboard. This drop test was passed.
(Disregarding appearance change such as loss of paint or distortion of the part where drop 
impact is applied.)

Handling of this unit

The waterproof performance may be degraded due to the strong water pressure when this unit is 
used deeper than 1.5 m underwater.

When this unit is splashed with detergent, soap, hot spring, bath additive, sun oil, sun screen, 
chemical, etc., wipe it off immediately.

Do not rinse with running water, such as tap water.

Waterproof function of this unit is for sea water and fresh water only.

Any malfunction caused by customer misuse, or mishandling will not be covered by the warranty.

Cards are not waterproof. Do not handle with a wet hand. Also, do not insert wet card into this 
unit.

Do not attach/remove the terminal cover (waterproof) or glasscover when your hands are wet or 
water droplets are present on this unit. If water droplets get inside this unit, the terminals may rust 
and cause malfunctions. Other types of damage may also result.

If you attach/remove the terminal cover (waterproof) or glasscover in a sandy or dusty 
place, sand or other foreign objects may adhere to the internal components, threaded 
portions (portions of this unit, terminal cover (waterproof) and glasscover with helical 
threads), rubber seals or other parts of this unit. Be extra careful when attaching parts to 

Preparation

(Important) About the Waterproof/

Dustproof and Anti-shock 

Performance of this unit

Waterproof/Dustproof Performance

This unit’s waterproof/dustproof rating complies with the “IP68” rating. Provided the care 
and maintenance guidelines described in this document are strictly followed, this unit 
can operate underwater, to a depth not exceeding 1.5 m for a time not exceeding 
30 minutes. 

*1

Anti-shock Performance

This unit has cleared a test conducted by Panasonic, which complies with MIL-STD 810F 
Method 516.5-Shock (a drop test performed from a height of 1.5 m onto 3 cm thick 
plywood). 

*2

Waterproofing is not guaranteed if the unit is subject to an impact as a result of being hit or 
dropped etc. If an impact to this unit occurs, it should be inspected (subject to a fee) by a 
Panasonic’s Service Centre to verify that the waterproofing is still effective.

Summary of Contents for HX-A1M



























































Reviews: