background image

- 15 -

Press the power button to turn on this unit.

About overheat detection

If the internal temperature of this unit rises during use, warning beeps will be heard and the power 
lamp will flash fast. This unit will then turn off automatically. To use this unit again, wait until it cools 
down.

This unit cannot be used until it cools down.

About battery level indications

You can check the battery level by looking at the recording mode lamps when you have turned on 
this unit.

The battery level can be checked for a few seconds after this unit has been turned on.

When the Extended Battery VW-BTA1 (optional) is used as a power source or the USB cable is 
connected to a PC, all the recording mode lamps light (in the same way as 100% to 76%) 
regardless of the remaining capacity of the built-in battery.

When the battery level reaches 10% or below, the power lamp flashes.

You can also check the battery level by looking at the “Image App” screen. (

l

28

)

Preparation

Turning this unit on/off

The power lamp is turned on.

To turn off this unit

Press and hold the power button for 
approximately 1 second.

The power lamp goes off after a while.

Battery level

100% to 76%

75% to 41%

40% to 21%

20% or less

Recording mode lamps

Summary of Contents for HX-A1M



























































Reviews: