Warning
● Do not make any modification to this product.
Doing so will result in an electric shock, a fire, or a drop.
● Do not use it at the place which dew
condensation generates by a quick temperature
change like the wind of an air-conditioner.
Doing so will result in an electric shock, a fire, or a drop.
● Do not use it in places with combustion gas.
Cause of the explosion.
● Install this product in accordance with the Electrical Equipment Technical
Standards (Law) and the Internal Wiring Regulations. Use proper
overcurrent circuit breakers on the primary side ofpower supply. Choose a
size of cable used to supply power to Factory Line suitable for overcurrent
circuit breakers to protect the branch circuit and for the rated current.
Not doing so will result in an electric shock, a fire, or a drop.
● Before check for the product, be sure to turn OFF the power supply.
Doing so may result in an electric shock .
● Make below the weight that can allow the weight hung to the duct.
Not doing so will result in a drop.
Caution
● this product is dedicated to ordinary indoor use, Do not
use it at the place which is subject to the influence of heat,
such as the upper part of a heater, or a place with moist
place and vibration, which receives blowing in of rain, and a
moist,,where corrosive gas, where the smoke rises
・A place with moist place and vibration
・A place which receives blowing in of rain, and a
moist place
・A place where corrosive gas, where the smoke
rises
・ The place which is subject to the influence of
heat, such as the upper part of a heater
Not doing so will result in an electric shock, a fire, or a
drop.
● Do not install the Factory Line duct.
Doing so may result in a fire.
● Do not slide putting the plug in the duct.
Poor contact will cause a fire.
● Do not cut the duct of the Factory Line 60 ,
because,the duct is of the Factory Line 60
subjected to special processing at both ends.
This may cause electric shock or fire fall.
● Use the range of －10 ℃ ～ 40 ℃ ambient temperature
The use with out of range, burn, or cause a fire.
● Orientation of the duct and shall decide the orientation
of the plug with breaker.
When installed in the opposite direction may cause electric
shock or fire fall.
● If you use facts as the branch circuit line is 100・
60,which mandates the installation of protective
devices on the regulatory impact (Article 171 of the
interpretation of the current technique),or installation
of protective devices, such as using the terminal pulg
with a breaker.
Failure to install protective devices may cause a fire.
●If you uses a remote control plug with breaker
terminal,and the operating voltage is 100V(not
available in 200V).
● For cutting work, wear protective equipment such as
safety glasses.
Not doing so may cause you to injure your finger.
●The opening of the duct,so as to be more aligned
towards the bottom.
Due to loose connection can cause a fire.
●And after cutting the sandpaper to remove burrs,etc.
Not doing so may cause you to injure your finger.
●In the Factory Line 100・60,in order to prevent the
misuse of 100V・200V,on the division must verify
the polarity of voltage,voltage display unit label part
number label bundled products,feed always put the cap
and plug-ins.
wrong polarity voltage,causing burns or fire.
●If you are using unique and relocation,match the duct
together with the polarity and voltage.
Not doing so will result in an electric shpck,a fire.
●If you use a 15A power plug to the Factory Line 100・
60,use a 15A or 20A branch circuit by law.
Not doing so will result in an electric shpck,a fire.
■ Be sure to read this Instruction Manual before installation, and then properly install the product.
■ Installing this product requires the qualification as an electrical worker. Be sure to ask a contractor
Installation Manual
Factory Line 100・60
The precautions describe what must be observed not to harm humans nor cause property damage.
Safety precautions
Be sure to observe the precautions fully
30
