Panasonic Diga DMR-EZ47, Operating Instructions Manual

Page: 90 / 100

90
RQT8853
Error Messages
On the Unit’s Display
Page
H , F
(“ ” stands for a ser
v ice
number.)

An error has occurred. The number following “H” or “F” depends
on the status of the unit. Check the items below and in the
Troubleshooting Guide. If the ser
v ice number still does not disappear
after the check, reset the unit (
¼
78, “To restore the unit if it freezes”).
−

If the ser v ice numbers fail to clear, note the ser v ice numbers and
contact a q ualified ser v ice person.
−
RC (“ ” stands for a number.)

The remote control and the main unit are using different codes.
Change the code on the remote control.
78
HARD ERR
(“HArd” and “Err” are alternately
displayed.) 
If there is no change after turning the unit on and off, consult the
dealer where the unit was purchased.
−
NO READ
(“NO” and “REAd” are alternately
displayed.)

The disc is dirty or badly scratched. The unit cannot record, play, or edit.
73

The disc may be incompatible or of poor q uality.
74 to 76

You ha v e used a lens cleaner and it has finished operation. Press
[

OPEN/CLOSE] on the main unit to eject the disc.
72

Displayed when the unit is started. This is not a malfunction.
−

The unit is carrying out its reco v ery process. You cannot operate the
unit while “

” is displayed.
−
FULL

There are already 16 scheduled recording programs. Delete
unnecessary scheduled recording programs.
18
UNSUPPORT
(“UNSUP” and “POrt” are
alternately displayed.)

You ha v e inserted a disc the unit cannot play or record on.
74, 75
UNFORMAT
(“UNFOr” and “MAt” are
alternately displayed.) 
You ha v e inserted a new DVD-R W /+R W or a DVD-RAM/DVD-R W
(DVD-Video format) recorded on other e q uipment.
You can format the disc when the format confirmation screen is displayed.
15, 45
“ ” is displayed on the
unit’s display.

This unit is confirming that it is connected with e q uipment
compatible with HDAVI Control.
−
F74

The HDMI connection could not be authenticated due to a transfer
malfunction. Consult the dealer where the unit was purchased.
−
F75

The HDMI connection could not be authenticated due to an internal
data malfunction. Consult the dealer where the unit was purchased.
−
U59

The unit is v ery warm.
The unit switches to standby for safety reasons. W ait for about
30 minutes until the message disappears.
Reinstall the unit in an area with ade
q uate v entilation. Do not block
the cooling fan on the rear of the unit.
−
U61

There was a power failure or the AC power supply cord was
disconnected while the unit was on. The unit is carrying out its
reco
v ery process. This process restores the unit to normal operation.
The unit is not broken. W ait until the message disappears.
−
U72
U73

The HDMI connection acts unusually.
–The connected e q uipment is not HDMI compatible.
–The HDMI cable is too long. Please use a cable 5.0 meters (16.4 ft.) or less.
–The HDMI cable is damaged.
−
U76

HDMI cannot be output because you are connected to a model that
does not support copyright protection.
−
U88

There was something unusual detected with the disc while recording,
playing or copying; there was a power failure or the AC power supply
cord was disconnected while the unit was on. The unit is carrying
out its reco
v ery process. This process restores the unit to normal
operation. The unit is not broken. W ait until the message disappears.
80
U99 
The unit fails to operate properly. Press [

/I PO W ER] on the main
unit to switch the unit to standby. Press [

/I PO W ER] on the main
unit again to turn the unit on.
−
M5821.indb 90 M5821.indb 90 2007/02/26 16:38:41 2007/02/26 16:38:41