background image

-20-

SW 2

SW 1

SW 3

Replacement of Expendables

Battery Replacement

The battery has a life of about 5 years.
The pan/tilt head has data on preset positions, limiter
positions and others stored in itself.  The stored data is
kept in the memory even if power is switched off, but
will be lost upon switching power off after the end of
battery life.
If the battery has lost power, replace it with a new one.

Removing the Battery

• Remove the 4 cover scress and take off the pan/tilt

head cover.

• Push the battery in the arrow direction (shown in

the figure) to slide it.

• Raise the sliding battery from the bottom indicated

by the arrow.

• When the arrow-indicated part of the battery has

come off the battery holder, pull the battery out
toward yourself.

Installing a New Battery

• Insert a new battery into the battery holder, its end

in the arrow direction.

• Push the battery in the arrow direction into the

holder.

Use the manganese dioxide lithium battery
CR2032 for replacement.

Motor Replacement

The drive motor of the pan/tilt head has a life of about 5
years.  If motor operation is not normal, the motor must
be replaced.

• Consult your dealer for motor replacement.

Gear Replacement

The gear has a life of about 5 years.  If preset stop
positions becomes less accurate, the gear must be
replaced.

• Consult your dealer for gear replacement.

Summary of Contents for AWPH300 - INDOOR PAN/TILT HEAD


























Reviews: