Panasonic AJ-PX5000G, Operating Instructions Manual

Page: 38 / 260

– 38 –
Chapter 3 Recording and Playback — Special recording functions
Special recording functions
When recording to P2 cards, the special recording functions of pre-recording, interval recording, one-shot recording, loop recording, and one-clip
recording can be performed by setting in the main menu
→ [REC/PB] → [REC FUNCTION].
Pre-recording
This function enables recording of video and audio from a fixed amount of time before recording is actually started.
Operation to start recording Operation to stop recording
Actual recording time
Pre-recording time
(Time)
1
Check the settings of each item in the main menu → [SYSTEM] → [SYSTEM MODE].
For details on system modes in which the pre-recording function can be used, refer to the table in “System modes and recording functions”
(page 53).
For details on menu operations, refer to “Setting menu basic operations” (page 147).
2
Set [ON] in the main menu
→
[REC/PB]
→
[REC FUNCTION]
→
[PRE REC], and set pre-recording by [PRE REC TIME].
f
The range that can be set for pre-recording time differs depending on the settings of the system mode (main menu → [SYSTEM] → [SYSTEM
MODE] → [LINE&FREQ] and [REC FORMAT]).
- When [LINE&FREQ] and [REC FORMAT] are set to [AVC-I100] in 1080P mode: 0 - 3 seconds
- When [REC FORMAT] is set to [DVCPRO] or [DV]: 0 - 15 seconds
- When other than above is set: 0 - 8 seconds
f
[P-REC] is displayed at the top of the display window. (page 87)
3
Press the <REC> button.
@ @ NOTE
t
[P-REC] indicator when [PRE REC] is set to [OFF]
When [PRE REC] is set to [OFF], [REC] is displayed until recording of video or audio to the P2 card is completely finished after recording is stopped.
Refer to “Information display such as interval recording/pre-recording” (page 87) for information about the [P-REC] indicator.
This indicator can be turned off by setting [OFF] in the main menu
→ [VF] → [VF INDICATOR] → [P-REC/i-REC].
t
Press the <USER> button to which [PRE REC] is assigned to simply toggle between [PRE REC] [ON]/[OFF]. For details, refer to “Assigning functions
to <USER> buttons” (page 67).
t
Video and audio according to the preset time sometimes cannot be recorded in the following cases:
- Immediately after the power is turned on
- After recording-related settings have been altered in the setting menu
- Immediately after the P2 card is inserted
- After playback or recording check is performed
t
The pre-recording function does not function in the following cases:
- When an item other than [NORMAL] is selected in the main menu
→ [REC/PB] → [REC FUNCTION] → [RECORDING] ([INTERVAL], [ONE SHOT],
or [LOOP] is set)
- When [SDI] is selected in the main menu → [SYSTEM] → [SYSTEM MODE] → [REC SIGNAL]
Interval recording
The camera will record at the set time intervals.
[REC TIME] set time [REC TIME] set time [REC TIME] set time
(Time)
[PAUSE TIME] set time [PAUSE TIME] set time
1
Check the settings of each item in the main menu → [SYSTEM] → [SYSTEM MODE].
For details on system modes in which the interval recording function can be used, refer to the table in “System modes and recording functions”
(page 53).
For details on menu operations, refer to “Setting menu basic operations” (page 147).
2
Set [INTERVAL] in the main menu
→
[REC/PB]
→
[REC FUNCTION]
→
[RECORDING].
3
Set the following related items in the main menu → [REC/PB] → [REC FUNCTION].
f
[HOLD]: Holds the [REC FUNCTION] setting after the power is turned off
f
[REC TIME]: Duration of each recording
f
[PAUSE TIME]: Standby time between recordings
f
[START DELAY]: Delay time from the time when the <REC> button is pressed until the time the first recording starts