– 158 –
Chapter 10 Maintenance and Inspection — Warning system
f
Press the playback related buttons.
f
Press the <THUMBNAIL> button.
f
Eject all the cards.
*5 The warning can be stopped by setting the [NEAR END CANCEL] item to [ON] and pushing the <DISP/MODE CHK> switch towards the <CHK> side.
Error code
Indicates the error code on the [HOME] screen of SmartUI when something has caused an error on the camera. Check the types of warning, and deal
with the error according to “Warnings description list” (page 157).
Code No.
Description
Type of warnings
E-27
Recording control error (viewfinder screen [P2 CONTROL ERROR])
1. System error
E-30
P2 card removal error (viewfinder screen [TURN POWER OFF])
2. Card removal error
E-38
P2 streaming microcontroller error (viewfinder screen [P2 MICON
ERROR])
1. System error
E-3F
Camera unit error (viewfinder screen [CAM MICON ERROR])
1. System error
E-40
Error in image sequence, generator lock input signal, or SDI input
signal (viewfinder screen [IRREGULAR FRM SIG], [PULL DOWN
ERROR])
5. Recording error, 6. Reference signal error
00000011
Recording error to P2 cards, etc. (viewfinder screen [REC RAM
OVERFLOW], [CARD ERROR
*
], [OVER MAX# CLIPS], [ERROR])
5. Recording error
Card warning code
Code No.
Description
Recording
Indication on SmartUI
E-70
The directory structure on the P2 card is
not supported. ([DIR ENTRY NG CARD]
(slot number) is displayed on the viewfinder
screen.)
Operation continues, but immediately back
up data on the card, and format the card
before using it again.
The warning code is displayed on
the [HOME] screen of SmartUI.
E-71
The maximum number of overwrites on the
P2 card has been exceeded. ([RUN DOWN
CARD] (slot number) is displayed on the
viewfinder screen.)
Operation continues, but recording
or playback may not be performed
properly. Replacement of the P2 card is
recommended.
Warning/error displays in the thumbnail operation and the USB host mode
r
Thumbnail
Message
Description
Action to take
CANNOT ACCESS!
Data cannot be accessed due to a content defect or some
other reason.
Ensure the health of the media and the clips.
CANNOT CHANGE!
For a clip with the [
] mark, where a thumbnail cannot be
generated with AVC-Intra 100 or AVC-Intra 50, the thumbnail
cannot be modified in the text memo position.
Set the [SYSTEM MODE] item on the setting menu [SYSTEM
SETUP] screen according to the clips.
CANNOT COPY!
Images cannot be copied.
Check the copy conditions.
CANNOT DELETE!
Images cannot be deleted due to contents version mismatch.
Match the device and contents version.
CANNOT FORMAT!
A P2 card problem or some other reason prevents formatting. Check the P2 card.
CANNOT RE-CONNECT!
Clips cannot be remerged because either clips that are not
recorded across multiple P2 cards are selected or other
reasons.
Check the selected content.
CANNOT REPAIR!
Clips cannot be restored because contents that cannot be
restored are selected or other reasons.
Check the selected content.
LACK OF CAPACITY!
There is not enough recording capacity left on the card.
Insert a card with sufficient recording capacity.
MISSING CLIP!
When all necessary P2 cards are not inserted, an attempt is
made to add a shot mark to the clips recorded across multiple
P2 cards.
Insert all P2 cards with the recorded clips and ensure that the
[
] incomplete clip indicator disappears, and then add the
shot mark.
NO CARD!
No P2 or SD card is inserted.
Insert the relevant medium.
NO COPY TO SAME CARD!
A clip cannot be copied to the card storing the original clip.
Copy the selected clip to a card that does not contain the
original clip.
NO FILE!
The specified file does not exist.
Check the file.
SAME CLIP IS SELECTED!
Clips cannot be copied because the clips already copied and
the original clips are selected.
Check the selected clips, and remove either the original clips
or copied clips, and then perform the copy operation.
TOO MANY CLIPS!
Too many clips are selected.
Reduce the number of selected clips.
UNKNOWN CONTENTS
FORMAT!
Contents version is mismatched.
Match the device and content versions.
UNKNOWN DATA!
The metadata character code is invalid.
The metadata character code is UTF-8. Enter valid characters
using a viewer.
USER CLIP NAME MODIFIED!
Characters in the clip name had to be deleted when adding a
counter value.
For the counter addition setting, the user clip name plus the
counter value can only contain up to 100 bytes. Characters in
the clip name are automatically deleted when the total number
of characters exceeds this limit.
WRITE PROTECTED!
The P2 or SD card is write-protected.
Insert write-enabled media.
