Panasonic AFP0HC32ET User Manual Download Page 8

Page: 8 / 102

Table of Contents

3.2

Initial Setting of Ethernet /IP .................................................................. 3-4

3.2.1

Ethernet Settings ..................................................................................... 3-4

3.2.2

Starting EtherNet/IP Setting Screen ........................................................ 3-5

3.2.3

EtherNet/IP Basic Configuration ............................................................. 3-6

3.2.4

Items of Ethernet /IP Basic Configuration ............................................... 3-7

3.3

Settings of Connection Using FP0H as Originator ................................. 3-8

3.3.1

Settings.................................................................................................... 3-8

3.3.2

Registering EDS File of Target Device ................................................... 3-9

3.3.3

Adding Target in Scan List .................................................................... 3-10

3.3.4

Setting IP Address of Target ................................................................. 3-11

3.3.5

Setting Tag/Instance ............................................................................. 3-12

3.3.6

Specifying Data Area Corresponding to Tag/Instance .......................... 3-14

3.3.7

Reference: Setting of Target [FP0H(B)] ................................................ 3-15

3.4

Settings of Connection Using FP0H as Target ..................................... 3-16

3.4.1

Settings.................................................................................................. 3-16

3.4.2

Adding I/O Map to Scan List.................................................................. 3-17

3.4.3

Registering Tag Name/Instance ID ....................................................... 3-18

3.4.4

Registering Data Area Corresponding to Tag/Instance ........................ 3-19

3.4.5

Reference: Setting of Originator [FP7] .................................................. 3-20

3.5

Confirmation of Load Factor Calculation .............................................. 3-21

3.5.1

Load Factor Calculation ........................................................................ 3-21

3.5.2

Displaying Load Factor Calculation ....................................................... 3-21

3.6

Saving EtherNet/IP Settings ................................................................ 3-22

3.6.1

Saving EtherNet/IP Settings in Project .................................................. 3-22

3.6.2

Saving/Reading EtherNet/IP Settings in File......................................... 3-22

3.6.3

Writing EtherNet/IP Settings to FP0H ................................................... 3-23

Tool Operation ................................................................... 4-1

4.1

Scan List Window .................................................................................. 4-2

4.1.1

Display Contents of Scan List Window ................................................... 4-2

4.1.2

Operations in Scan List Window ............................................................. 4-3

Summary of Contents for AFP0HC32ET







































































































Search results

Summary of Contents for AFP0HC32ET

Reviews:

Panasonic AFP0HC32ET, User Manual, Page: 8 / 102

Search results

Summary of Contents for AFP0HC32ET

Reviews: