manualshive.com logo in svg

Panasonic AFP0HC32ET, User Manual, Page: 70 / 102

Share
Download
Panasonic AFP0HC32ET User Manual Download Page 70

 

Startup and Operation 

5-2 

 

5.1  Startup Operation of Cyclic Communication 

5.1.1  When FP0H is Originator 

When the FP0H is originator, the FP0H operates in the following order after it is powered on.  

Power ON

Resolves IP address.

Starts each communication 

application task.

Starts EtherNet/IP task.

Connects to targets according to 

Scan List.

Starts sending/receiving data from 

targets whose connection are 

established.

Refreshes the data received by 

FP0H from targets.

Communications with all targets are 

normally performed.

IP address fixed flag 

(R9342) turns ON.

EtherNet/IP preparation 

done flag (R9350) turns ON.

The corresponding bits of

cyclic communication

normal node tables turn ON.

EtherNet/IP all nodes normal 

communication active relay 

(R9351) turns ON.

Resolved.

Started.

Refreshed.

All nodes are 

communicating.

 

KEY POINTS

 

•

 

For confirming if the connection with each target is established or not, 

check "Cyclic communication normal node table". The cyclic 

communication state node table can be read by F465 ETSTAT instruction. 

The communication state of each connection can be checked. 

•

 

For confirming that the connections with all targets have been established, 

check the all nodes normal communication active relay (R9351). 

 

Summary of Contents for AFP0HC32ET







































































































Reviews:

No comments