Palram Sunscape Installation Manual Download Page 20 | Manualshive

Page: 20 / 20

background image

20

Palram Americas

PALRAM AMERICAS
9375 Commerce Circle, Kutztown, PA 19530 USA
800-999-9459
Palram.com

SUNSCAPE® and Palram® are copyright 2019 by Palram Industries Ltd. All rights reserved.

SUNSCAPE® Roof Panels are made from high-quality polycarbonate material. To clean them:

• Use a soft, clean sponge or a soft, clean 100% cotton cloth.
• Use lukewarm water and a mild dishwashing detergent.
• Rinse the surfaces with cold water.
• Dry with a soft cotton cloth if desired
• To reduce the appearance of water spots, avoid washing in direct sunlight.

• SUNSCAPE

®

Cleaning Guidelines

• Pressure washers are not recommended.
• Do not use abrasive or high alkaline cleaners.
• Do not use sharp objects, squeegees or razors.

«
...
18
19
20

Summary of Contents for Sunscape





















Reviews:

No comments

Related manuals for Sunscape

Brand: Voxx Pages: 7

Two-Knife Booklet Trimmer-A1

Brand: Canon Pages: 32

Perfect Binder-C1

Brand: Oce Pages: 82

Brand: AAT Pages: 6

Brand: Obelink Pages: 2

Brand: wattio Pages: 15

Brand: Oki Pages: 20

WORKCENTRE C2424

Brand: Xerox Pages: 2

WaterGuard CM2300

Brand: Mobeye Pages: 32

Brand: PROAIM Pages: 3

Brand: UBEXi Pages: 16

Brand: Acebil Pages: 11

Brand: amora Pages: 84

Brand: FormFit Pages: 4

Brand: Homelite Pages: 1

Brand: Vaxcel Pages: 5

Brand: WABCO Pages: 48

Door/Window Sensor

Brand: Sage Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands