background image

ILF 33/44/55                                                                                                                       Installation Manual     

 

 

Rev 1.1 

                                                              

    52  

 

12 

Decal Placement and Inspection 

For  operator  safety,  all  decals  appearing 

in  “Decal  Kit”  must  be  in  a  conspicuous  place  on  control  side  of 

liftgate. This is typically a combination of decals on the liftgate and truck or trailer body. Please make sure to 
place the maximum capacity decal (C) on driver and curb side. 

 

Important:  Never  remove  or  paint  over  any  decal.  If  any  decals  below  require  replacement  contact 
Palfinger Liftgates.

 

 

Decal Kit 

Decal 

Qty. 

Part No. 

Description 

ATG-URGWA 

Urgent Warning: Elevating gate instructions 

ATG-BKR 

Circuit Breaker Reset (must be placed where the circuit 

breaker was installed) 

ATG-XXXX 

Capacity (please check the serial number plate to find out your 

specific capacity) 

ATG-RESET 

Circuit Breaker Protection 

ATG-WLH 

Warning: liftgate can crush 

ATG-CTN 

Caution: Always stand clear of platform area 

ATG-CAB 

Liftgate Shut-Off (Place Decal next to the On-Off Switch in the 

Cab) 

ATG-WNG 

Warning: Use handle to open (Must be located underneath 

handle (main section) 

ATG-FT 

Notice for Foot Control 

Strip 

 

Conspicuity Tape (Place tape along bumper) 

ATG-ILF 

Operating Instructions (Place in control box) 

85-0816-000* 

Operating Instructions (Place on the curb side of vehicle body 

above control box) 

 

*Stake  and  Flatbed  Vehicles:  It  is  recommended  to  install  a  plate  on  the  stakes  of the  vehicle  to  serve  as  a 
surface to install Decal L. Part number 60-0115-200 maybe used for flatbed vehicles with no stakes. 

Fig. 27

 

 

 
It is the installer„s responsibility to determine the proper application of the Conspicuity tape (J), and to 
ensure  that  the  vehicle  meets  DOT  and  federal  lighting  regulations.  Keep  in  mind  that  there  are 
different requirements depending on the classification of the vehicle. This document is not intended to 
replace published agency regulations, and it is strongly recommended that the installer references the 
Code of Federal Regulations (CFR) which can be viewed at http://www.ecfr.gov.

 

 

 

Summary of Contents for ILF 33
























































Reviews: