manualshive.com logo in svg

Palax C900.2, Instruction Manual, Page: 34 / 38

Share
Download
Palax C900.2 Instruction Manual Download Page 34

34 

1-2020 

 

 

Translation        

9.16 

Tightening and lubrication of the conveyor chain 

 

The conveyor is hydraulically driven and equipped with automatic tightening of the 

chain. 

 

Lightly lubricate the chain every day. 

 

9.17 

Cleaning the conveyor 

 

Keep the conveyor free of debris to ensure its trouble-free operation. 

 

Especially in winter, it is important that the conveyor is always cleaned at the end of 

every working session. 

 

The conveyor can also be washed with a high-pressure washer. The chain must be lu-

bricated after washing. 

 

9.18 

Washing the machine 

 

Wash the machine occasionally with a high-pressure cleaner. This is especially im-

portant if the machine is left standing for a longer period of time. Lubricate the machine 

after washing. 

 

Note! Do not direct the water jet onto electric devices or bearings. 

 

9.19 

Storing the machine. 

The machine is intended for outdoor use but it is recommended to keep it under cover or 
indoors for longer standstills to avoid corrosion and malfunctions the corrosion may cause. 

Summary of Contents for C900.2







































Reviews:

No comments