Palax C900.2 Instruction Manual Download Page 30 | Manualshive

Page: 30 / 38

Palax C900.2 Instruction Manual Download Page 30

30

1-2020

Translation



There is an adjustment screw at the blade side end of the in-feed conveyor with which

you can change the path of the belt and make it run straight.

9.9

Replacing the in-feed conveyor belt

1. Remove the bearing of the pusher on the operator’s side from the frame.

2. Remove the cover, Fig. 20

3. Remove the support plate, Fig. 21

4. Remove the old belt from its place.

5. Thread the new belt in place.

6. Fix the removed parts and tighten the belt, refer to point 9.9.

Figs. 20 and 21

9.10

Direction of rotation of the belt



Check the correct direction of rotation of the belt in accordance with the arrow, while

replacing the belt.



During the infeed operation, the belt must run in the direction of the arrow.



The belt joint may break, if the belt is installed in the wrong way.



Check the belt for tightness at regular intervals.



The drive roller must not slip.

9.11

Changing the oil in the angular gear

1. Twist open the bottom plug, Fig. 22, and drain off the old oil. Put the plug in place.

2. Remove the plugs at the top and in the centre. Refill with oil through the upper plug

opening to level with the plug opening in the centre.

3. Filling capacity about 0,5 l. Oil type SAE 80.

4. Put the plugs in place.

«
...
28
29
30
31
32
...
»

Summary of Contents for C900.2







































Reviews:

No comments