manualshive.com logo in svg

Palax C900.2, Instruction Manual, Page: 12 / 38

Share
Download
Palax C900.2 Instruction Manual Download Page 12

12 

1-2020 

 

 

Translation        

2  TAKING DELIVERY AND SETTING UP THE MACHINE FOR 

OPERATION 

2.1 

Lifting the machine 

The machine can be lifted with a forklift truck from both sides. The places for the lifting 
forks are marked with decals. There is also a lug for lifting the machine on the upper part 
of the machine frame. 
 

2.2 

The transport set-up and unpacking 

 

The machine is delivered almost ready assembled and with the conveyor attached. 

 

In order to avoid damage during transportation, the machine is delivered partly disman-

tled so that all the protruding levers and the hitching parts of a tractor-powered ma-

chine and part of the protective covers have been removed and packed separately. 

 

The extension table for the in-feed conveyor and the loading conveyor are in the 

transport position. 

 

The angular gear is filled with transmission oil. 

 

2.3 

Acceptance inspection 

 

Check the delivered goods without delay. 

 

If the product shows transport damage, contact the transport company and your dealer 

immediately. 

 

 

Fig. 1 

 

2.4 

Main parts of the machine, Fig 1 

1.  In-feed conveyor 

2.  Oil tank 

3.  Saw-blade cover 

Summary of Contents for C900.2







































Reviews:

No comments