manualshive.com logo in svg

Palax C900.2, Instruction Manual, Page: 27 / 38

Share
Download
Palax C900.2 Instruction Manual Download Page 27

27 

1-2020 

 

 

Translation        

9  MAINTENANCE OF THE MACHINE 

NOTE !

 

 Always use genuine spare parts prescribed by the manufacturer. 

 

NOTE !

 

To clean up the guide rails for the pusher, drive the Palax Optimi once a 

day to its extreme position (55 cm) and after that, return it to the desired cutting 

length. 

WARNING!

 

Always stop the machine and disconnect it from the power sources be-

fore performing any service measures. 

 

9.1 

Removal and change of the crosscut blade, Figs. 13 and 14 

.     

Figs. 13 and 14 

 

 

The crosscut saw-blade must conform to the standard EN 847-1+A1. 

1.  Loosen the attachment screws for the protective cover, a 13 mm wrench. 
2.  Open the protective covers. 
3.  Loosen the blade-bolt using the special wrench delivered with the machine. Right-

hand thread, a 36 mm wrench 

4.  Carefully clean the surfaces of the flanges before re-installation of the blade. 
5.  The gap between the guide blocks and the blade must not be less than 5 mm. 

 

NOTE ! 

 

While installing the blade, make sure that the locking pin (A) is in place! 

 
 

 

A 

Summary of Contents for C900.2







































Reviews:

No comments