manualshive.com logo in svg

Palax C900.2, Instruction Manual, Page: 28 / 38

Share
Download
Palax C900.2 Instruction Manual Download Page 28

28 

1-2020 

 

 

Translation        

 

9.2 

Tightening the V-belts 

 

The Palax C900.2 is equipped with automatic tightening devices for the belts. 

 

9.3 

Replacement of the V-belts, centre shaft / saw-blade shaft 

1.  Remove the crosscut blade as instructed in point 9.1. 

2.  Slacken the tightening device of the belt. 

3.  Change the belts, 4 pcs. Type SPA 1500. 

4.  Carefully clean the surfaces of the flanges before re-installation of the blade. 

5.  Attach the protective covers. 

 

9.4 

Sharpening the blade, hard-metal blade 

 

The hard-metal blade can be sharpened "lightly" using a diamond file. 

 

Depending on the cleanliness of the wood, as many as 500-1000 bulk cubic metres of 

wood can be processed with a hard-metal saw-blade without re-sharpening. 

 

The best sharpening result and durability of the blade is achieved when the saw-blade 

is sharpened using an appropriate grinding machine with a diamond disc. 

 

9.5 

Setting the saw-blade, hard-metal blade 

 

The hard-metal blade does not normally show any tendency for tension fault, but espe-

cially when a blunt saw-blade is used for cutting and it gets very hot, tension faults can 

occur. 

 

Leave the prestressing of the hard-metal blade to a professional. 

 

9.6 

Spare blade 

 

If you are processing a lot of firewood, we recommend that you obtain a spare blade 

 

9.7 

Replacement of V-belts, angular gear /centre shaft 

1.  Remove the rear cover plate from the machine. 

2.  Slacken the V-belts using the disengagement lever for the transmission. 

3.  Remove the attachment plate of the oil pumps from the frame, 4 pcs. M 10 screws, 

17-mm wrench. 

4.  Replace the old belts by new ones, type SPA 1607, 4 pcs. 

5.  Tighten the V-belts by releasing the disengagement lever for the transmission. 

6.  Install the pumps in place. NOTE! MAKE SURE THE COUPLING ALIGNMENT IS 

MAINTAINED! 

7.  Replace the rear cover. 

8.  If the machine is equipped with an electric motor, loosen the attachment of the mo-

tor and move the motor outwards as much as is necessary to slip the belts between 

the claws of the claw clutch. 

 

 

Summary of Contents for C900.2







































Reviews:

No comments