manualshive.com logo in svg

Palax C900.2, Instruction Manual, Page: 19 / 38

Share
Download
Palax C900.2 Instruction Manual Download Page 19

19 

1-2020 

 

 

Translation        

 

Fig. 9 

 

WARNING!

 

Never remove from the machine the plate that prevents the simultane-

ous operation in two modes.  

Always remove the PTO shaft before operating the machine by electricity. 

 

3.11 

Operation under cold conditions 

When an electrically powered machine is operated in a temperature below -10 degrees 
Centigrade, we recommend using less viscous hydraulic oil, such as ISO VG22S multi-
grade oil or synthetic hydraulic fluid, because a machine with electric drive takes full revo-
lutions right from the start of operation. 
 
In cold weather, it pays to reduce the speed of the discharge conveyor to a minimum. 
Opening the protective net for the splitting chute facilitates cold starting. 
Doing it this way requires the least power at the start-up stage. 
 
It also pays to pull down the disengagement lever for the transmission for a cold start. 
Then only the angular gear will start running and the gearbox oil will warm up. After this, 
stop the machine, release the disengagement lever for the transmission and restart the 
machine.  
 

3.12 

Electric heater for oil tank 

A 300 W electric heater carpet with adhesive tape attachment and a thermostat is availa-
ble as an option for the hydraulic oil tank. The starter comes as standard equipped with an 
operating switch for the heater, Fig 8 E. Heating the oil for 1-2 hours is sufficient to enable 
smooth starting. 

 

The size of the heater carpet is 200 x 300 mm 

 

Output 300 W 

 

Equipped with a thermostat 

 

Strongly adherent glue for attachment of the carpet 

 

Summary of Contents for C900.2







































Reviews:

No comments