Painless 60608 Installation Manual Download Page 28 | Manualshive

Page: 28 / 52

background image

27

23. Plug the grey 13 pin 4L60E transmission solenoid connector (labeled

TRANSMISSION

) into the mating connector port located on the passenger side

of the transmission just behind the lube level indicator tube.

24. Plug the black two pin vehicle speed sensor connector (labeled VSS) into the

vehicle speed sensor located on the passenger side of the tail shaft housing of
the transmission.

«
...
26
27
28
29
30
...
»

Summary of Contents for 60608





















































Reviews:

No comments

Related manuals for 60608

Brand: Ubisys Pages: 54

Brand: MILL Pages: 14

PURMO INVOICEFLYER

Brand: RADSON Pages: 2

Brand: Hozelock Pages: 40

Brand: KYK Pages: 23

Brand: Crestron Pages: 5

W3000 - SA Subwoofer - 200 Watt

Brand: Sony Pages: 2

Brand: Sony Pages: 2

STR-DE997 - Fm Stereo/fm-am Receiver

Brand: Sony Pages: 2

Brand: Sony Pages: 2

SAW2500 - SA Subwoofer

Brand: Sony Pages: 1

Brand: Sony Pages: 5

STR-K402 - Fm Stereo/fm-am Receiver

Brand: Sony Pages: 36

STR-K700 - Fm Stereo/fm-am Receiver

Brand: Sony Pages: 46

STR-K402 - Fm Stereo/fm-am Receiver

Brand: Sony Pages: 51

STR-DE997 - Fm Stereo/fm-am Receiver

Brand: Sony Pages: 71

STR-DE997 - Fm Stereo/fm-am Receiver

Brand: Sony Pages: 78

Brand: Sony Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands