Pacific Sun Kore 7th User Manual Download

Page: 31 / 79

Page 31

Kore 7th Manual / kHLab Edition

4. Kore 7th Desktop/Laptop Application Installation

4.1. MS Windows Application Installation

The installation software creates a shortcut to Pacific Sun Kore 7th application in your

Start menu and on your desktop. As an example the following steps are for a new computer

with Windows 10 operating system when the application has been installed first time. The

Kore 7th application is also fully compatible and supported under with Widows 7 operating

system.

To download Kore 7th

application go to

http://pacific-sun.

eu/shop/dosing-stations/kore-7th-

khlab-edition/

Select

Download

■▶

Download

Software

for MS Windows OS.

Downloaded file will be "

rar

compressed file.

Important:

You need to decompress

this file

before starting the installation

process.

After decompressing the

installation file run installation

program by clicking “

setup

”.

Summary of Contents for Kore 7th
















































































Search results

Summary of Contents for Kore 7th

Reviews:

Related manuals for Kore 7th

Brands by name

Popular brands

Pacific Sun Kore 7th, User Manual

Search results

Summary of Contents for Kore 7th

Reviews:

Related manuals for Kore 7th

Brands by name

Popular brands