Pacific Sun Kore 7th User Manual Download

Page: 20 / 79

Page 20

Kore 7th Manual / kHLab Edition

11.

Make sure that the DHCP option

is Turned OFF on the Kore 7th dosing

station. This will make your Kore

7th doser current network settings

permanent. They won’t change after

reboot, power OFF/ON.

Go to

WiFi Station

settings and scroll

down to

Special Settings

Select option:

Static IP

Under

Static IP address

specify

your

NEW

Kore 7th IP address:

192.168.1.227

Click

Change!

Important!

When using

Static IP

your Kore7t IP

address will

NOT

change after doser or

home router restart.

Important!

Take a note of your Kore 7th doser’s IP address. It’s necessary for later

router configuration. This is how your Kore 7th is identified on your home

network.

In this example Kore 7th home

[Private/Internal IP]

address is

192.168.1.227

Summary of Contents for Kore 7th
















































































Search results

Summary of Contents for Kore 7th

Reviews:

Related manuals for Kore 7th

Brands by name

Popular brands

Pacific Sun Kore 7th, User Manual

Search results

Summary of Contents for Kore 7th

Reviews:

Related manuals for Kore 7th

Brands by name

Popular brands